1974 CB550 Build
- Thread starter alexcb550
- Start date
alexcb550
Active Member
Finished wiring the entire front end today. This is the extent of my wiring harness. So glad I decided to make my own harness. If anyone needs some diagrams to help simple wire their Honda four, pm me.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
alexcb550
Active Member
Electrical is all done except for the tail light and rear turn signals "thus the extra looms of wiring" Running only two fuses on the bike, a 60a from the battery terminal to the starter solenoid, and a 30a from the starter solenoid to ignition. Placed the new regulator rectifier combo where the horn use to be for adequate airflow. Petcock valve was relocated 4.5" towards the front as there was interference with the carbs. Buchanan's started working on my rims today. Starting to see the end result in sight! Pretty damn excited! Btw: my hidden stickers add 5whp
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
Looking good. Digging the paint.
I fabbed up a little rear fender that attaches to the swingarm on my 360. Pretty low profile and keeps the crap out of my UNIs. I'll post a pic shortly.
I cut out a more attractive section of the stock plastic fender from the 360 and used that as a mold to lay up fiberglass to make the fender itself. Food for thought.
I fabbed up a little rear fender that attaches to the swingarm on my 360. Pretty low profile and keeps the crap out of my UNIs. I'll post a pic shortly.
I cut out a more attractive section of the stock plastic fender from the 360 and used that as a mold to lay up fiberglass to make the fender itself. Food for thought.
alexcb550
Active Member
Thats a nice fender! I think I have settled with something going on the center part of the frame before the carbs but still tinkering.
Made my own rear set brackets and they are drying from paint. Also got in my mandrel bend U section from summit racing and 12" reverse cone exhaust from DCC. Should be able to fab up the exhaust tomorrow. And yes I do some of my painting in a old tire balancer. I have a handful of them from when I use to own a shop.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
Made my own rear set brackets and they are drying from paint. Also got in my mandrel bend U section from summit racing and 12" reverse cone exhaust from DCC. Should be able to fab up the exhaust tomorrow. And yes I do some of my painting in a old tire balancer. I have a handful of them from when I use to own a shop.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
alexcb550
Active Member
https://vimeo.com/141734453
Walk around of the bike and engine start with new exhaust.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
Walk around of the bike and engine start with new exhaust.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
Smooooth growl.
john83
Over 1,000 Posts
alexcb550 said:
Gotcha. I've got a similar 4-1 exhaust on my 550, it also came with the bike. I can't remember if it's a Mac or Kerker but they look pretty similar. The muffler on it give the bike a pretty high pitched note at cruise. What you've got going on is more the sound I'd like to hear.
alexcb550
Active Member
Wasn't too bad to do, about a $100 muffler from DCC, and a little bit of bent tube. Not sure what location you are in, but if you are in Northern California, I can get it done in a couple hours with a case of beer as trade I have extra mandrel bent tubing too.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
I have extra mandrel bent tubing too.74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0
alexcb550
Active Member
coyote13 said:
It is close but clears. I can also heat the bracket and bend it away slightly if it starts touching. Luckily, the stock shifter pedal is made out of steel so it is pretty easy for me to cut it and weld on a linkage bracket to match the rear set. Heres some pictures.
74 CB550 build thread: http://www.dotheton.com/forum/index.php?topic=66127.0