1974 CB550K Cafe Racer!!!!!

See attached pic....
 

Attachments

  • CARB550.jpg
    CARB550.jpg
    128 KB · Views: 288
Perfect. Then that IS just a breather. You'll note there is one on the other side as well. So that piece really isn't needed at all. They can be "open" to the air if you want, or the last person had "tubes" running them down and away from the bike as they originally must have been. Carry on sir!

Edit: The other one might be blocked too depending upon where it was in the set of 4.
 
Should I worry about replacing the rubber things on the link arms? If you can't tell I am pretty new to all this haha.
 
Got another pic? Not sure exactly what you are referring to. And don't worry about being new to it, we all were once, it all depends on where you came from,who you grew up with, and who taught you (if anybody other than the internet!)
 
I'm not 100% positive, but I don't think those are available new anymore.

A great site though is http://www.cmsnl.com/ the prices are in Euros (so double US prices), and shipping is expensive, but on many parts their the only place that have them!
 
By the way, that's the rustiest carbs I've seen someone work on! I think there perfectly salvagable, I'm just sayin' :)

When you gonna get those bad boys in boiling lemon juice!?
 
Its actually mostly grease and dirt. There is so much dirt on this bike. Mud dobber nests everywhere. I got some lemon juice but then I looked at some pictures of people who had done it. That finish is ugly! I am either gonna drop them in a parts washer or boiling water with dish detergent.
 
hmenzies said:
Its actually mostly grease and dirt. There is so much dirt on this bike. Mud dobber nests everywhere. I got some lemon juice but then I looked at some pictures of people who had done it. That finish is ugly! I am either gonna drop them in a parts washer or boiling water with dish detergent.

Yeah the lemon juice isn't so great on the actual carb bodies, leaves a powdery residue, but after going over them with some soft steel wool, I was able to get them looking good, but yeah you're probably right, it was a hassle, but it might be I left them in too long, maybe a 5 to 7 minute limit.
 
LearnAsIGo! said:
Yeah the lemon juice isn't so great on the actual carb bodies, leaves a powdery residue, but after going over them with some soft steel wool, I was able to get them looking good, but yeah you're probably right, it was a hassle, but it might be I left them in too long, maybe a 5 to 7 minute limit.
Woyuld you mind posting a picture of your carbs?
 
Last carbs I did, I soaked them in Pine Sol (the real stuff, not the funky colors) and they came out looking like fresh cast metal. I let them soak overnight, o-rings and all, then took a toothbrush to them under hot water and tossed `em back in the bin of Pine Sol. Then I rinsed them thoroughly in scalding hot water. Even the brass that was stuck came dislodged. But I never got the pine scent off them!

Just my $0.02
 
hmenzies said:
Woyuld you mind posting a picture of your carbs?
Here ya go!
 

Attachments

  • Picture 001.jpg
    Picture 001.jpg
    1.7 MB · Views: 303
  • Picture 002.jpg
    Picture 002.jpg
    1.7 MB · Views: 286
I still need to do some more polishing, and change a few screws. Here's the before pics.
 

Attachments

  • Dirty Carbs 001.jpg
    Dirty Carbs 001.jpg
    1.6 MB · Views: 310
  • Dirty Carbs 002.jpg
    Dirty Carbs 002.jpg
    1.6 MB · Views: 366
  • Dirty Carbs 003.jpg
    Dirty Carbs 003.jpg
    1.6 MB · Views: 295
Those aren't all that dirty before hand! haha (maybe I find really crappy bikes compared to you!) Good trick though, I wouldn't mind mine smelling like pine! ;)
 
Back
Top Bottom