'77 CB750 Overhaul (HELP A NEWBIE OUT!!!)

deviant said:
Pump rubber should be pliable and without cracks or pinholes. You can hold it to the light to check. The rod should be smooth and clean. I light emory or scotch bright to polish it up. Also, make sure that whole circuit is free and clear. Gaskets can be bought through 4-into-1---> http://4into1.com/carburetor-parts/

Thank you. On the accelerator pump online they show new ones coming with a rubber bellow. Mine had no such thing on the inside so I have no reference of where one would need to go.

Thoughts?
 
deviant said:
Pump rubber should be pliable and without cracks or pinholes. You can hold it to the light to check. The rod should be smooth and clean. I light emory or scotch bright to polish it up. Also, make sure that whole circuit is free and clear. Gaskets can be bought through 4-into-1---> http://4into1.com/carburetor-parts/

Small pinhole in the pump rubber where it meets the rod so I can get a new one of those. Just need to figure out where that rubber bellow goes on it.

Also, I checked the site you mentioned here and it has the gasket that goes into the bottom of the bowl but still not the one that every one of my carb bodies has on it. Were these things not even supposed to be there?
 
K+CO Moto said:
Also, I checked the site you mentioned here and it has the gasket that goes into the bottom of the bowl but still not the one that every one of my carb bodies has on it. Were these things not even supposed to be there?
Do you mean that huge gasket in your pic between the float bowl and carb body? That's supposed to be a rubber o-ring dealio that's shaped like the profile of the float bowl. Somebody made those gaskets you show in the pic.

honda_carburetor_float_bowl_rubber_gasket_16010_405_004_K22B_CB750K_CB750F_CB750_1977_1978_o_ring__60911.1380751926.750.750.jpg
 
deviant said:
Do you mean that huge gasket in your pic between the float bowl and carb body? That's supposed to be a rubber o-ring dealio that's shaped like the profile of the float bowl. Somebody made those gaskets you show in the pic.

honda_carburetor_float_bowl_rubber_gasket_16010_405_004_K22B_CB750K_CB750F_CB750_1977_1978_o_ring__60911.1380751926.750.750.jpg

Exactly what I was thinking (someone made it). Yeah, I've found the o ringy things which is what comes in most rebuild kits.

So I'm sitting here freaking out that I don't have some obscure oem gasket to go back on it.

So is it worth me getting those made again or do I just clean those off and use the standard gaskets that come with the kits?
 
No reason to make gaskets. My guess is someone wanted to fix a leaky bowl and went to Autozone instead of buying the right o-rings.
 
IIRC the slide needle on the 77-78 did not have an adjustable clip. Look for model markings on the side of your carb to make sure you're looking at the right carb kits. I believe the stock units should be PD42A
 
deviant said:
You're right. They do not. They have a clip, but only one groove.

So you guys are saying that my bike has a non-stock set of carbs on it? I'll check the numbers when I get home...

Interesting.
 
Could just be a different set of needles than stock, I think (again IIRC) those PD's were the only carbs on the SOHC CB750 series that had an accelerator pump. Might fact check that one, I could be wrong.
 
It was 77 and 78.

Many poke holes in both sides of the diaphragm thinking it is plugged by mistake... not so the part is/ has one hole for the SOHC, if your #2 carb does not get a squirt of gas when opening the throttle the diaphragm is toast, the passage is plugged or the plunge rod is not in contact with the throttle/out of adjustment, maybe even lack of fuel to the accelerator pump. likely someone bumped the slow jets when it was not needed, they are press fit, but a good set of linemans pliers will bite with little presure and twist them out then put them back with a brass drift and small ball peen don't tap the jets direct if at all possible. Just go to stock settings maybe up one size on mains with the K&N's and pipe and go from there, always bench sync before reinstalling.

Man I wish I had a way to run a sensor and tune these things right, but too spendy for my blood.
 
Tune-A-Fish said:
It was 77 and 78.

Many poke holes in both sides of the diaphragm thinking it is plugged by mistake... not so the part is/ has one hole for the SOHC, if your #2 carb does not get a squirt of gas when opening the throttle the diaphragm is toast, the passage is plugged or the plunge rod is not in contact with the throttle/out of adjustment, maybe even lack of fuel to the accelerator pump. likely someone bumped the slow jets when it was not needed, they are press fit, but a good set of linemans pliers will bite with little presure and twist them out then put them back with a brass drift and small ball peen don't tap the jets direct if at all possible. Just go to stock settings maybe up one size on mains with the K&N's and pipe and go from there, always bench sync before reinstalling.

Man I wish I had a way to run a sensor and tune these things right, but too spendy for my blood.

Right now the main jet is a 125

Slow (pilot) is a 58!

Needle is set at the highest pin

Need to measure the float heights still

Pod filters on the bike and a 4 into 1 Kerker exhaust.


I have plugs that are wet and black and many signs that seem to point to running rich but what is strange is that the dude before me put these upgrades on to increase airflow, added the larger jets to increase fuel mixture but then had the needle set for leanest setting.

I keep wondering to myself whether it is actually rich or lean but it will be hard to tell until we get it back on the bike and do a few tests, I suppose.

Haven't bench synced a carb before but looking forward to trying it!
 
By the way how does one clean out the accelerator pump nozzle in #2? Most every other passage I was able to get a super thin copper wire through to ensure it wasn't blocked but the odd position of that has me wondering how to clean it out...
 
K+CO Moto said:
By the way how does one clean out the accelerator pump nozzle in #2? Most every other passage I was able to get a super thin copper wire through to ensure it wasn't blocked but the odd position of that has me wondering how to clean it out...

Barymans carb cleaner and PB blaster... hit it with PB let it sit then blow it out with cleaner, dry with air and PB again between the two most any hole will give way.
 
Float verification: You can bench set the floats exactly correct with this method if you are willing to level up a spot and make a rest to set the carbs on, I set them just below the gasket like as little as a mm or less but so you can see it.

Just crack the drain open and see the fuel level.

7dafe6fbd73d2bd4ed3a0cac6d812f8e.jpg
 
Tune-A-Fish said:
Float verification: You can bench set the floats exactly correct with this method if you are willing to level up a spot and make a rest to set the carbs on, I set them just below the gasket like as little as a mm or less but so you can see it.

Just crack the drain open and see the fuel level.

7dafe6fbd73d2bd4ed3a0cac6d812f8e.jpg

Nice! I'll try it.
 
125 should be pretty close for the main, but 58 is HUGE. I think you should be somewhere around 38-40. Sounds like the PO was trying to remedy the rich bottom end by leaning out on the needle. Don't think there's a needle with enough notches for that trick to work!
 
coyote13 said:
125 should be pretty close for the main, but 58 is HUGE. I think you should be somewhere around 38-40. Sounds like the PO was trying to remedy the rich bottom end by leaning out on the needle. Don't think there's a needle with enough notches for that trick to work!

Number on the jet relates to the diameter of the jet right?

And the slow jet specifically affects throttle off acceleration?

So he buys a MASSIVE slow jet thinking he needs to upgrade it because of the pods and exhaust... see's it's wrong and maxes out the needle to try to compensate instead of new slow jets?

Sound about right?

So I should try to buy a few sets of lower sizes to try, right?

Anyone got a great source for those?
 
K+CO Moto said:
Number on the jet relates to the diameter of the jet right?


They are not always the same....


http://www.jetsrus.com/FAQs/FAQ_mikuni_vs_dynojet_vs_keihin_sizes.htm
 
I don't really but you can try eBay not likely to find Kiehin new. The way I have a few is from donor carbs, you might try and buy a set of parts carbs if you can.

Search keihin push in jets... you will find keyster is the only new source
 
Got it. Will do.

Actually, I have valve job, cam timing, plugs, coil test all happening this weekend. I'll make sure those things are in order first prior to finishing the carb stuff.

Any other suggested maintenance checks are welcome.... :o
 
Back
Top Bottom