80 CB750C Carb Synch

acturner

New Member
How difficult is it to synch carbs? I've got a CB750C where 1 and 2 are firing, but 3 and 4 are not. There is spark from 3 and 4 plugs. I've got carb repair kits I will be using to replace all the parts on the carbs. And I have the Clymer book telling me what to do. Also, is this a good carb tuner? http://www.motionpro.com/motorcycle/partno/08-0411 Or is there a cheaper and better tuner?

I called a shop here in Austin and they told be that it's a minimum labor of $400, and with parts (carb kits they would do) could cost up to $800. Just trying to save some cash.

Thanks in advance for the help.
 
First off, hello! Glad to see another person on the site. I'll chime in with my personal thoughts as I'm sure others will.

I'll start with the sync tool: I have that exact one and I enjoy it. No more lead, has instructions and works well. With that said, there ARE much cheaper home-made versions. Lookup manometer on this site and on the net. Theres a $50 mod thread on here that has tons of great things. But I think someone even claimed to make one for something like 10 bucks, (I'm sure they had some of the parts already though) So do a few searches on manometers and you'll get some cool stuff.

After saying all of that. I think synchronizing carbs is easy. But I clean carbs for people weekly. I usually start with cleaning the carbs out before I buy the kits since 99% of the time I can clean the carbs, jets, passages and re-use the same float bowl gaskets and it won't leak and works great. If you just need some jets and don't have to replace all the parts, find your local shop and see if they have them in stock. A place near me sells jets for 3.50 each. And DennisKirk has TONS of main jets (and pilot jets) for relatively cheap too. The biggest PITA is getting all four of those carbs out and back on the bike! Goodluck and PM me if you have any questions, I've got a lot of pictures of the insides of carbs that may answer any questions you have.

Bruno
 
Synching carbs is not rocket science, but it is science. The Keihin's on our 750's are generally easy to synch. They have mechanical linkages and you can bench synch them by eye pretty much. There's a main linkage bar that goes across all 4 of them that turns with the butterfly valves. Open each one and tighten the set screw on the linkage bar. Move to the next one and do the same, and so on. They'll be at about 95% after just doing that. If you want it any better, build a manometer, or pay a hundred bucks for a shop to vacuum synch them. Good luck!
 
Hmm, if you've got 3/4 not firing, have you checked to make sure those two bowls have fuel? 3/4 shares a fuel line, so if there's blockage in a filter or a kink in the line, it could cause those two cylinders to not fire. The sync is easy once you understand the concept. Each cylinder is pulling a vacuum through the carb throat. The amount of vacuum is determined by how much air is allowed to flow past each slide. The more vacuum, the more fuel. Carb sync tools test the vacuum between the cylinder and the carb. You want each cylinder to be pulling the same vacuum, and hence the same fuel. Without the carbs in sync, each cylinder will be firing unevenly and pulling on the crankshaft unevenly. When all is in balance, the bike will purr!
 
OneWheelDrive said:
Hmm, if you've got 3/4 not firing, have you checked to make sure those two bowls have fuel?

That's what I was thinking too. A bad sync won't stop a cylinder from firing, and the symptoms are most notable at slow speeds. At higher speeds, the butterflies are open, and fuel will be flowing freely, at perhaps slightly less volume than the other carbs. Should still run. I think your problem is elsewhere.

cheers
ian
 
Back
Top Bottom