'81 SR250 trying to find a new battery

It's a lithium ion battery. When the voltage gets too low, it eats itself up. It's dead, Jim.
 

Attachments

  • lithium_window.gif
    lithium_window.gif
    34.2 KB · Views: 859
Good news! Because I ordered the battery through Amazon I alerted them that the battery did not work as I was led to believe and it was under warranty they were able to just go ahead and provide me a full refund! So, awesome. So now, I guess I'm gonna just go ahead and order an EarthX so I don't run into an over-discharge problem again... 3 questions for you Sonreir; 1) Should I get a new regulator/recitifier or stick with my stock one, and 2) Can I just use a regular ol' lead acid battery charger on this if I hit the over-discharge limit somehow where it cuts off? (Trying not to spend a ton on a charger I have a trickle one from harbor freight but I know that probably won't be good for it) 3) Should I for sure be getting the ETX6A? I see that it replaces regular 6V batteries so I just want to make sure I shouldn't be buying the ETX12A
 
1.) Stock one on the 80s bikes is usually up to the task, but a new one might be a good idea if your current one is suspect.

2.) A trickle charger will work. Don't use a charger that has a desulfation mode, though.

3.) ETX6 is still a 12V battery. The 6 stands for 6Ah equivalency. Should work just fine on your bike.
 
Sonreir said:
1.) Stock one on the 80s bikes is usually up to the task, but a new one might be a good idea if your current one is suspect.

2.) A trickle charger will work. Don't use a charger that has a desulfation mode, though.

3.) ETX6 is still a 12V battery. The 6 stands for 6Ah equivalency. Should work just fine on your bike.

Roger that, good to hear my trickle will be legit. Thanks for the help


Sent from my iPhone using Tapatalk
 
As a canuck with my bike plated year round, I have a heated vest that runs off this bike as well. I had contemplated and LED headlight to reduce the draw but with the light off/start circuit it's not a big deal.

Long story short, if you tuck the battery away like I did under the cafe/solo seat with impossible to access terminals, I bought a spare connector to connect the trickle charger to the heated vest plug that pokes out under the seat, just behind the regulator.

I have not had to put the bike on the charger at all. Even with a stubborn cold start on some days.
 
Most bikes do not charge the batteries until the engine is spinning at higher rpms so I'd guess (as others have commented) that you drained your battery running it at idle for so long. Maybe if you had connected a battery tender while it was running (and set up a fan for engine cooling and paint off-gas removal)?
 
Well I ordered the earth x ETX6A and it kept dying on me as well. So its definitely not the correct battery for this bike... Called up the Earth X people and they had me go with the ETX18B... The 6A had nowhere near the amount of amp hours I need for me bike. So just an FYI to anyone. I'll update when I get the 18B this weekend but I'm sure its gonna be OK after that.

This was my experience with the ETX6X: put the battery onto my bike, started the bike up let it run idle for a bit took the battery back off in order to put into a new custom battery box, put it back on and got no voltage from the battery at that time. I then thought the overdischarge protection of the battery must have turned on somehow so I went ahead and put it on a correct charger with jumper cables attached to it and my lead acid battery as earth x's website says to bring it back up to life to charge with resetting the overdischarge function. This worked so I put the battery back on and the same thing happened, I got one good idle out of it turned it off and when I tried to start again had no voltage. Charged the battery AGAIN and just let it sit on my dresser when it was fully charged back up buy itsself with no charger or anything checked the voltage the next day and it was back to zero.
 
Sonreir said:
How long were you idling it?

For a minute or two

I'm not sure how it would be an issue with anything else considering it had been running fine with a lead-acid battery. What could it possibly be?

The Lead Acid Equivalent Amp Hours on the ETX6A are 6AH.... in my manual it says the standard Lead Acid Battery for my bike has 12AH, wouldn't that be the cause of my problem right there?

If I was idling this thing for hours I would understand, but if this battery isn't going to let me idle for a few minutes what the heck is the thing worth. On top of that when I brought the battery back and reset the over-discharge function I charged it to where it should be and let it sit for one, two days on my dresser... when I checked it's voltage after that it was back to 0V so somehow the over-discharge kicked back on. After telling this to the people at Earth X, the one have my bike listed as needing the ETX18B which has a Lead Acid Equivalent Amp Hours of 18. What they said is I probably killed one of the cells because the Amp Hours on the ETX6A were too low.

If you think it is something else please share.

Here are the electrical system specs from my manual including the standard battery, regulator/rectifier etc...:
https://www.dropbox.com/s/ih3133k30d5vhwg/SR250%20Elec%20Specs.png?dl=0

The Standard Battery Specs are
12V Voltage
113A CCA
12 AH

ETX6A Battery

12 Voltage
80A CCA
6AH Amp Hours

ETX18B Battery

12V Voltage
230A CCA
18AH Amp Hours

The ETX6A Didn't have nearly the CCA or the Amp Hours of the original battery my manual calls for, so that is where I and the people at earth X believe the problem is from and why I might've fried a cell in it.

If I'm totally wrong here please help.
 
I did a test on the two that I have with the diode function on my multimeter and as far as I can tell it is working correctly from that

Also, if it wasn't working correctly wouldn't I have had problems with my lead acid battery as well?

I'm confused as to why the ETX6A should work if the amp hours and cold cranking amps are so far under the specs of the standard lead acid battery. Just going off of that shouldn't it make sense that the ETX18B I'd what I should be going with?
 
A 6Ah rating means you should be able to pull six amps for a full hour before battery failure. If you're saying the battery failed in just two minutes, then you were pulling 180 amps, which would have definitely blown your fuse and/or set your bike on fire. Not to mention that the ETX can't even supply 180 amps.

Possible that you got a dud battery from the factory?

And for what it's worth, my 695cc Ducati (V-twin with electric start) uses an ETX18 as well (though has previously run well on an ETX12 for over a month).
 
Sonreir said:
A 6Ah rating means you should be able to pull six amps for a full hour before battery failure. If you're saying the battery failed in just two minutes, then you were pulling 180 amps, which would have definitely blown your fuse and/or set your bike on fire. Not to mention that the ETX can't even supply 180 amps.

Possible that you got a dud battery from the factory?

And for what it's worth, my Ducati (V-twin with electric start) uses an ETX18 as well (though has previously run well on an ETX12 for over a month).

That's all I can think is that the battery was no good to begin with especially after bringing it back to life and it over discharging shut off just sitting on my dresser for two days.

I don't know much at all about batteries if you can't tell ha, but I'm hoping I have success with the 18B.... If I have problems with that then obviously it's something else but ive done a lot of checking my P's and Q's on all other electrical fronts. Any other suggestions on things to check? I checked for any parasitic drain and found none, checked my regulator/rectifier with the diode function in my multimeter and just did a good visual check on all my electrical work etc. Is there something I may be missing? If your able to check out that pic in the Dropbox link I added a fee posts above can you see if the stock reg/rect I am using would be okay or a problem? I'd like to avoid spending the money for a new one if possible but if I need one I need one. Its been 80 degrees all week and I'm ready to put rubber on pavement haha
 
Have you tried measuring the voltage across the battery terminals while the bike is running?

Get things warmed up and then check voltage. Should be around 13V or so. Then give it some gas and you should see it climb to just over 14V.
 
Sonreir said:
Have you tried measuring the voltage across the battery terminals while the bike is running?

Get things warmed up and then check voltage. Should be around 13V or so. Then give it some gas and you should see it climb to just over 14V.

Yup I did that as well and that's what I got
 
Just an update, I got and installed the ETX18B and its working great after a few test runs and a few times just sitting and idling for a while. IThe previous Earth X battery and the Antigravity battery I had previously tried had neither the cold cranking amps nor amp hours anywhere close to what the stock battery in the manual for my bike calls for so all I can think it that this is why it took the 18B to work because every other thing electrical wise is solid and the way it needs to be with nothing extra and nothing gone, I even went through replacing some tattered wires and shoring up connections making sure everything was good to go before I went through this battery stuff. It makes me think this would be even more correct after the people at EarthX said this is the battery I should have been using from the start. Thanks for the input though ya'll
 
burkejt1 said:
Just an update, I got and installed the ETX18B and its working great after a few test runs and a few times just sitting and idling for a while. IThe previous Earth X battery and the Antigravity battery I had previously tried had neither the cold cranking amps nor amp hours anywhere close to what the stock battery in the manual for my bike calls for so all I can think it that this is why it took the 18B to work because every other thing electrical wise is solid and the way it needs to be with nothing extra and nothing gone, I even went through replacing some tattered wires and shoring up connections making sure everything was good to go before I went through this battery stuff. It makes me think this would be even more correct after the people at EarthX said this is the battery I should have been using from the start. Thanks for the input though ya'll

So after running with the ETX18B for a week or so after I got through some other issues I worked out that weren't electrical I'm riding down my street and all power cuts out... Pull the battery out and the case looks like the battery blew up on the inside (pic attached)... Called EarthX and they assume it was because my older charging system overloaded it but because they made do mention of this possibly happening when I ordered the battery from them they're going to replace it or refund me.... If I were to buy a new rect/reg would this solve the problem? And would the 12v single phase one on sparck moto be a correct choice to replace my old one with? At this point just trying to decide whether to keep messing around with these lion batteries that have yet to work out for me or go back to the stock lead acid one.
 

Attachments

  • IMG_20150609_120301:nopm:.jpg
    IMG_20150609_120301:nopm:.jpg
    3.3 MB · Views: 343
Back
Top Bottom