any ideas for mounting points for KZ400 B1 rearsets

RobK

Active Member
New to the site and been spending a bunch of time thinking about how to mount rearsets on the machine, (especially as clip ons are on their way from Fast from the Past).

Has anyone created mounting brackets for a KZ400? There aren't a a lot of mounting points near in the area where I think they should be, (which seems like right in the middle of the triangle in the pic below - perhaps somewhat low).

I have a couple of ideas, but would prefer not to re-invent the wheel if someone has already had a good idea about how to get rearsets attached to the frame.

Thanks all.

Below is a pic of my pic for reference.
 
Looks like I stumbled across a pretty elegant solution.

A little bit of steel, a welder and some trawling on eBay for some used sport bike units and I should have some purdy lil rearsets...

Below are pics I found from a site detailing someone's conversion of a 400f into a vintage racer.

Cool site, worth a look...

http://www.oldrice.com/Cafecorner.htm

I think the same procedure should get me to where I want to be.

And it just made me realize that that little triangle can probably face the angle grinder.
 

Attachments

I am using this same principle on my kz. welding on some tabs to mount fzr600 controls. I will probably have to put a tab on the brake side lever to mount the rod to, but no big deal. the sets on fzr's are steel except for the peg. I found that most of the newer controls, say from 99 up, were to radically swept to use.
 
beater said:
I am using this same principle on my kz. welding on some tabs to mount fzr600 controls. I will probably have to put a tab on the brake side lever to mount the rod to, but no big deal. the sets on fzr's are steel except for the peg. I found that most of the newer controls, say from 99 up, were to radically swept to use.

Yeah - I noticed after I mounted my GSXR reasets, that even on the bike above ^^^ that the angle is wrong (the mounting holes need to be straight up and down) - not sure how he resolved it, I'm going to use a little triangle of 1/4" aluminum flat-bar to correct the angle. This has caused an issue on the shift side as I can't find linkages long enough, but will probably be better on the brake side as I'll now be closer to the drum.

Brake side is a all new as I've ground off the old lever (along with side cover tabs, center-stand tabs, seat mounts, and anything else I could find to nix without effecting stop, go and turn). I'm going to try and directly link the connecting rod from the drum lever arm to the GSXR lever. If that doesn't work I'm going to go cable, but as that sounds like more work, and as a light rear brake is preferable, I'm hopeful that modding the connecting rod will be sufficient.

Still working on the mould for the new seat/cowl, before building up a rolling chassis, so probably a few weeks out from the fine tuning on controls.
 
I've come up with pretty much the same conclusion on my 77 KZ400. The rear triangles are getting cut off and I'll be welding on a couple of tabs to mount the universal set of rearsets to that I'm waiting on from Thailand. I had tried mounting a set of Yamaha R1 rearset pegs and levers directly to the passenger peg mounts but as many here pointed out they were too low and too far back. Here's the rearsets I ordered.... http://tinyurl.com/y9sta5q
 
Ok has anyone figured out the dilema of how to run the rear drum with the new rearsets? I'm concerned I won't have clearance from the swing arm to run a rod back to the drum lever. I'm going to look at reversing the drum lever and having it point up this afternoon and see if it's even feesable.
 
the drum goes both ways. you can run it push or pull. the levers from an fzr are steel, and you can weld an eye for the clevis wherever you want. See my build thread. pics are loaded.
 
It is highly recommended that you do not push the brake rod to stop. It will flex under load.
 
DrJ said:
It is highly recommended that you do not push the brake rod to stop. It will flex under load.

true dat. Especially if you are keeping the stock pot metal rod. However, if you section/sleeve/fab a new rod, that goes MOSTLY away. lol..either way, you can weld a tab on for it to pull.
 
So I have a 1976 KZ400 and already cut off the passenger peg triangle. I am thinking about going the thailand rearset route. Have you received the rearsets yet noahdog? Are they good quality/ worth it?
 
slushie07 said:
So I have a 1976 KZ400 and already cut off the passenger peg triangle. I am thinking about going the thailand rearset route. Have you received the rearsets yet noahdog? Are they good quality/ worth it?

They are very light but scratch pretty easily so the quality isn't the greatest. Considering they were almost a hundred bucks less than the cheapest good set they're worth trying out on my bike. I'm still working out exact placement and linkage set up to the rear drum lever. I want to get my seat mostly done so I can get a true height of seating placement before I mount the rearsets. How high their placed on the bike will make a big difference on how I design the linkage to the rear I'm sure.
 
Back
Top Bottom