Bbq paint or Caliper paint for Exhaust?

YogiBear

Over 1,000 Posts
I'm curious if any of you have experience with either. I am debating on getting a 4 into 1 pipe for my 750 and am considering the potential coating options. I've also considered ceramic coating (which I've used on a car part or two) but I think for the sake of touching up rock chips and what not, I think paint may be a good option depending on if it will heat up and flake off like the high heat dulicolor/vht engine paint I've witnessed do.
 
They have flame proof paint thats intended for headers and comes in a rattle can, or even powder coat (i think)
 
How about exhaust paint? :o
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_x_7141561-P_x_x?cm_mmc=ACQ-_-Google-_-GPLA-_-7141561&ci_src=17588969&ci_sku=7141561&ci_gpa=pla&ci_kw=&gclid=CPyOp7e6uLwCFStnOgodZC0AOQ
 
Finnigan said:
They have flame proof paint thats intended for headers and comes in a rattle can, or even powder coat (i think)
I believe what you are thinking of is VHT, correct? If so, I have seen it flake off a 4 into 1 pipe my Brother painted.
 
YogiBear said:
I believe what you are thinking of is VHT, correct? If so, I have seen it flake off a 4 into 1 pipe my Brother painted.

Thats odd, did you prep the surface first??
 
SONIC. said:
How about exhaust paint? :o
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_x_7141561-P_x_x?cm_mmc=ACQ-_-Google-_-GPLA-_-7141561&ci_src=17588969&ci_sku=7141561&ci_gpa=pla&ci_kw=&gclid=CPyOp7e6uLwCFStnOgodZC0AOQ
I think that's the same stuff finnigan is talking about.
 
Yes thats the stuff I was thinking of. Might have to bite the bullet and powdercoat them, no way in hell that will flake off and it would only be 50$ at a decent shop
 
I would just paint them, then wrap them.

Not everyone likes the look, or the arguable function, but it seems like the cheapest solution.
 
Did he cure the VHT flameproof paint? You have to cure it. After it's completely dry, you have to heat it to 250 degrees for 30 min, then let it completely cool. Heat it to 450 degrees for 30 min, then let it completely cool. Heat it to 650 degrees, then let it completely cool. You can also cure it on the bike by running it for 10 min, 20 min, and 20 min letting it cool in-between each heat up.

http://www.vhtpaint.com/products/flameproof/
 
The issue with exhaust paint is that most people are using it over chrome.
TO paint over chrome you really need to roughen the surface up heavily, and any section left shiny (no matter how small) is going to flake when you heat it to 600 degrees.

Sand blasting is the best option
 
deviant and SONIC., I think those two are probably why his is flaking. I know he roughed up the chrome but not to the point that sand blasting would do and I don't know if he properly heat cycled it. I didn't know you had to do either.
 
Yogi, I have used Rustoleum's "Ultra" B-B-Q paint with good success on two exhausts. The Zooks Kerker and the CB750's head pipes. I did sandblast the chrome on both sets and did cure it with short runs at first then gradually increasing, letting it cool between sessions.


SPHhuBlkSpL.ashx
 
Hoosier Daddy said:
Yogi, I have used Rustoleum's "Ultra" B-B-Q paint with good success on two exhausts. The Zooks Kerker and the CB750's head pipes. I did sandblast the chrome on both sets and did cure it with short runs at first then gradually increasing, letting it cool between sessions.


SPHhuBlkSpL.ashx

Thanks HD. How long has it been since you painted both exhausts? How are they holding up?
 
About a thousand miles on each now. Looking good so far. The oldest is on the Zook. Tiny bubbles if you look very closely. It is adhiering well still.
 
Hoosier Daddy said:
About a thousand miles on each now. Looking good so far. The oldest is on the Zook. Tiny bubbles if you look very closely. It is adhiering well still.
Cool. I'll give that stuff a whirl on mine. :) Thanks for the recommendation HD.
 
Bbq paint or Caliper paint for Exhaust?

I've had the same rustoleum on my RD chambers and had no issues in 2 years
 
Re: Bbq paint or Caliper paint for Exhaust?

S Majure said:
I've had the same rustoleum on my RD chambers and had no issues in 2 years


2 stroke exhaust doesn't (normally) get as hot as a 4 stroke.


Not saying the paint isn't up to the job, but you will have less issues with your paint than on a 4 stroke.
 
Back
Top Bottom