cb360 running poorly, low rpm spuddering, midrange bogging, high rpm rocket.

CB360BT

New Member
Hey guys, I recently got my cb360 running after honing, re-ringing, etc... The engine has basically been gone through completely and I had the carbs worked on by CrazyPJ (great service by the way) to run K&N pod filters. I have been riding it a little and trying to make the final adjustments. I have the timing spot on, valves set, points gapped.
When I have low load on the bike, 1/2 throttle at low rpm it runns pretty good until midrange 4-6k rpm. If i try to give it the beans from a standstill there is the breakdown; 1-4k runs ok with some spuddering from time to time, 4k-6 it really struggles with spuddering and bogging, but as soon as i get out of the bogging at 6-7k it takes off like a rocket presumably all the way to redline (I havent pushed it quite that hard yet). Any thoughts on where to start getting this thing running right?
side note, I have noticed that my fuel lines have bubbles of air and I do suspect I may have a slightly blocked petcock, maybe this is the cause of my issues?
Thanks guys!
 
Check the rubber on the intake manifolds too. Mine seemed O.K. when I had them off. Now that I have the bike running, it runs well cold, but gets finicky warm. Turned out the manifolds look good cold and seal, but when warm, start leaking air.

New ones on the way.

If you haven't replaced them, they are over 35 years old and could use a freshening up. It makes it easier to remove the carbs when needed too.

Check timing too. Advance too.
 
here are the plugs



The timing was done static, I may be getting a timing light tonight just to be sure.
The intake boots seem to be in really good shape.
 
Double check those intake boots. I thought mine were fine. Cold they were good. Warm, they leaked

This was a bad one. Caused idle misfire, backfires:

leftcarbbootcracks.jpg



This one is bad, but the right cylinder never seemed to have an issue:

rightcarbbootholeshy.jpg


The cut was not easily seen when installed.

I learned a lesson from these...new ones on the way...
 
WWW.Hondacb360.com has them in stock now. He ships with some gasket material to make your own gasket.

I ordered from DCC because HondaCB360.com was out of stock. I should of waited a day.

Western Honda has them too.

I would chose HondaCB360.com first, as they are accumulating a nice inventory of CB360 parts. They are not the cheapest, but are competitive and the shipping is reasonable. I like supporting the small business that is catering to my needs. He has throttle cables, brake parts, shocks, exhaust, etc...His catalog is going to be increased shortly too. I talked to Zephyrking (Brenden) who is the proprietor of the store, and he is a CB360 owner and nut case like us. So if you can, do business with him.
I just bought throttle cables, front brakes, tach cable, and some nice clamps for the boots from him. I've ordered some of the gaskets from him too.

I have no financial interest, but I have been purchasing from him, and helping him choose and test products. We are trying to find a suitable cam chain tensioner replacement for the bike. I have a spare engine, so I can help test fit parts.

But they are available at a few places. So pick your place. They are $30-$35 each, plus shipping. A bit for 2 pieces of rubber, but Sophie can't seem to live without them.
 
I did just find some small cracks, ordered from cb360 just a second ago.
I will inspect the boots more when I get them off, the cracks I noticed were extremely small but I'm sure there are more severe ones hiding under the clamps or on the inner side thats hard to see.
 
I would also use some sealant on the gaskets. Don't overtighten the boots either, they will warp.

Eventually, all the 37+ year old rubber is going to need replacement anyway. It looses something over the years. Kind of like CrazyPJ. He was a lot more flexible 36 years ago...LOL
 
Back
Top Bottom