CB400T Café Build...but be patient this will take a while!!

And now for the fabric, and somewhere to place me arse.....
 

Attachments

  • photo 1-3.JPG
    photo 1-3.JPG
    2.4 MB · Views: 333
  • photo 3-2.JPG
    photo 3-2.JPG
    158.8 KB · Views: 330
  • photo 2-2.JPG
    photo 2-2.JPG
    154.8 KB · Views: 328
A little more progress made...now to the the powder coaters......

At last all the mods are finished...and I can now get the parts powder coated and start building for real...
rere brake set up is not sexy but it works well....
 

Attachments

  • brake 1.JPG
    brake 1.JPG
    1.7 MB · Views: 340
Component parts ready for Powder coating....

At last I'm ready for powder coating...dropping them off tomorrow..
 

Attachments

  • photo 3-3.JPG
    photo 3-3.JPG
    3 MB · Views: 317
  • photo 2-4.JPG
    photo 2-4.JPG
    2.7 MB · Views: 333
Now I have to start the build for real...back from powder coating....
 

Attachments

  • photo.JPG
    photo.JPG
    1.1 MB · Views: 320
LOL I suppose. I was thinking you had everything ready but I didn't check if you still had to wire etc. that adds time and beer. If you were just putting it together they are pretty fast bikes to assemble.
 
Maritime...i'll mix it between Molson and Guinness...plus a few craft beers to spice it up a bit....missing a few parts so can't get started until they arrive.
 
Nice, that sounds like me, I can't afford to buy all craft beers, especially in NB so I buy the cheap macro brews like from Molson or Moosehead or Labatt and a few of the good craft ales and start with the good stuff and switch to the cheap stuff after a few and taste is less important ;D


The best is when I have my own brews on hand but I sadly have not gotten my setup finished in the new house to pump out the ales.......yet
 
Home Brew...never tried that, a mate did it a few times, but it was short lived.....I think he got fed up with everyone drinking his free beers, serves him right for continuing to invite the soup hounds around.
 
drduke said:
Home Brew...never tried that, a mate did it a few times, but it was short lived.....I think he got fed up with everyone drinking his free beers, serves him right for continuing to invite the soup hounds around.
LOL it does draw the riff raff if you are even remotely good at it. I started out when broke in University, and found out I could brew pretty good stuff, then the new Kits came out with the worth as a liquid vrs tar in a can and those turn out as good or better then some of the good micro brews out there and they can be tweaked to be even better. Works out to about $7 bucks a 12 pack vrs $24 for micro brews here.
 
LOL I know, the worst part of the whole process is washing and sanitizing bottles. So I am trying to save up for a Keg/tap/CO2 system, only issue there is I will be drunk and fat cause beer on tap at home in the shop would be a very good and very bad thing LOL.
 
YEEAAAH I know what you mean.....look at me I started this bike September 2012....and its still in bits, and that's without drink.....last think I need is a Canadian, telling a Irish man all about cheap beer...recipe for disaster...or worse!!!
 
Ha, I know, I am of Irish heritage so fully understand ;D

Edit: all this talk of beer is making me thirsty, I may have to just leave work early and hit the store on the way home.
 
LOL.......unfortunately, I'll be getting no drink tonight...the missus has other plans for me, and it's not the bedroom kind either.
 
drduke said:
LOL.......unfortunately, I'll be getting no drink tonight...the missus has other plans for me, and it's not the bedroom kind either.

Funny how that goes. I got the same thing last night.
 
Some Trumpets on them there Carbs...!!!

These arrived today...not sure if they are overkill, can't put them on the bike yet as it's stripped down again...they will either be the dogs...or a disaster.
 

Attachments

  • photo 4.JPG
    photo 4.JPG
    779.7 KB · Views: 324
  • photo 3.JPG
    photo 3.JPG
    774.7 KB · Views: 363
Back
Top Bottom