CB400T Café Build...but be patient this will take a while!!

may offer this up to the frame tomorrow, sure what else would I be doing on a Saturday.
 

Attachments

  • photo 1-11.JPG
    photo 1-11.JPG
    928.5 KB · Views: 320
  • photo 2-11.JPG
    photo 2-11.JPG
    904.5 KB · Views: 306
Any thoughts on the velocity stacks???

I'm not sure myself but would appreciate any comments good or bad???
 

Attachments

  • photo 1.JPG
    photo 1.JPG
    648 KB · Views: 318
  • photo 2.JPG
    photo 2.JPG
    643.2 KB · Views: 329
  • photo 3.JPG
    photo 3.JPG
    650.6 KB · Views: 314
Beer O'Clock

Afternoons work complete...time for a beer...
 

Attachments

  • photo 1.JPG
    photo 1.JPG
    898.6 KB · Views: 354
  • photo 2.JPG
    photo 2.JPG
    940.9 KB · Views: 292
I see they have a filter cover as well as the screens, they have to be better then the shitty emgo pods. they look good at least. Let us know how they are once you fire the bike up.
 
Will do Maritime...I reckon I need the microfiber filters...dust, rain etc...keep the shit out...as I'm not going to run a hugger or rear mudguard.
 
Maye consider a very small shield that hangs down under the seat to stop big rocks from damaging the filter. You could put something black that would dissappear there, but otherwise they look good and the shape should make them easier to tune from what I read.
 
Yeah...might be a idea alright.....I do hope they are easy to tune...with the K&N filters I have on when I was testing the engine it was running very rich....definitely needed jetting..but that's another days work.
 
massive restriction with the screens or the fabric you need WAY more surface area for performance
a LARGE uni foam filter clamped on those stacks, without the screens, would do nicely
 
Thanks for the comments, the fabric screens are there just as a add on,
only would run them if caught in the rain to stop all the shit entering,
Do you think the foam would be better than the wire mesh, no restriction,
really with the mesh...or is there?
 
actually that wire mesh is quite restrictive,huge loss of area and the drag induced is quite high you would be better off with very course screen(large holes) in the same bowl shape
but large clamp on foam filters would be great and it looks like you have room for them as well
the streets are incredibly dirty an engine wont last long unfiltered
 
Cheers for that..i'll see what happens when I get it fired up and tuned...I will make the call then...somehow foam filters
for me are for dirt bikes....I think I would prefer K&N's if I had to change.
 
a few more picture updates...

Ignore the tyres and wheels, these still have to be renewed.
 

Attachments

  • photo 2.JPG
    photo 2.JPG
    346 KB · Views: 446
  • photo 3.JPG
    photo 3.JPG
    657.4 KB · Views: 344
90% finished..

its been a while since I posted, as not alot has happened, I got stuck in again last weekend and did some more work today,
I had a problem with the kick starter, after much tooing and froing only option was to break open the casing again, so since last weekend
and this, I have stripped the bike down again, split the crankcase, fixed the kick starter and built the bike back up again...see some pic below
of the various stages.
 

Attachments

  • FullSizeRender-8.jpg
    FullSizeRender-8.jpg
    626.7 KB · Views: 343
  • FullSizeRender-7.jpg
    FullSizeRender-7.jpg
    728.5 KB · Views: 330
  • FullSizeRender-6.jpg
    FullSizeRender-6.jpg
    844.2 KB · Views: 321
  • FullSizeRender.jpg
    FullSizeRender.jpg
    564.6 KB · Views: 333
  • IMG_0748.JPG
    IMG_0748.JPG
    591.5 KB · Views: 346
  • IMG_0742.JPG
    IMG_0742.JPG
    574.5 KB · Views: 339
  • IMG_0740.JPG
    IMG_0740.JPG
    595.5 KB · Views: 326
  • IMG_0736.JPG
    IMG_0736.JPG
    1.3 MB · Views: 340
CB400T Café Build...getting near end game...

Getting closer to finishing this little racer.....send the hubs off to get new rims and spokes fitted...last week...just a matter of time now...roll on the spring.
 

Attachments

  • IMG_0921.JPG
    IMG_0921.JPG
    297.2 KB · Views: 316
  • IMG_0922.JPG
    IMG_0922.JPG
    691.8 KB · Views: 314
  • IMG_0923.JPG
    IMG_0923.JPG
    739.2 KB · Views: 320
Dyno results

just a extra 5hp from stock...better than nothing I suppose....sounds sweet with the Velocity stacks and Triumph Bonny pipes.
 

Attachments

  • dyno results.jpg
    dyno results.jpg
    322.2 KB · Views: 334
hey thats great ! 15% increase is nothing to sneeze at
izzat open stacks ? cause i would bet that lingere' on them stacks is killin at least 2-3hp
 
Nice looking bike. 5hp increase is always good. Is that 5hp improvement compared to when you started or to a good stock bike or to some other baseline?
 
5hp extra is from the stock figures of a new bike, so guess it's not bad.
The cover on the velocity stacks are only used for dusty or rainy conditions
I would not have them fitted for normal use, as I'm still working on the bike best leave them fitted to keep any dust out.
 
Decided on the authentic look number plate with hand painted letters/numbers.......
 

Attachments

  • IMG_0972.JPG
    IMG_0972.JPG
    1.3 MB · Views: 368
Back
Top Bottom