CB450 First build- Dallas, TX

onehundredton

New Member
Just to start, this is the first bike Ive ever done. I don't have a lot of experience building bikes but I have a knack for these sort of things and Im pumped to get this thing rollin! Ive been watching a lot of other builds on here over the past year and i figured it was time to start my own thread.

About a year ago i got the fever to buy a bike but i didnt know what i wanted so i started researching and stumbled upon cafe racers. I was sold. So i started shopping for a donor bike and i found this...

Here's a little bit about the bike...

Its a 1973 CB450 that I found on craigslist last summer for $900. It had 6k original miles, in pretty good condition and ran pretty well so I maxed out my credit card and paid cash for it ;D

I wanted to ride it so cut the fenders down, threw on some clip ons, found an old 350f tank at the bone yard lined the tank bondo and painted it, hacked up the old seat pan and made my own seat, new tires and I was rolling for a while.

I thought it looked pretty cool, but i wasn't really satisfied because there were a lot of little things that weren't complete or just weren't to my liking.

I laid the bike over while I was on campus a few months ago, due to an oil leak (possibly from the head gasket?) and caused me to lose traction going around a corner. I trailered the bike home and now I've decided to put the money into it to totally build the thing from scratch.

I'd be more than happy to hear any of your advice and I'll probably have a few questions along the way so heres my build!
 

Attachments

  • IMG_0395.JPG
    IMG_0395.JPG
    1.7 MB · Views: 379
  • IMG_0565.JPG
    IMG_0565.JPG
    2 MB · Views: 308
Re: CB450 First build- College Kid from TX

I like it! I'm just starting my own build, so I'll be following yours to learn what I can from you.

Robb
 
Re: CB450 First build- College Kid from TX

Thanks man. That's actually a picture of it before I laid it over. Last week I stripped the thing down to the frame and im going to get to work on the top end once my gasket set and piston rings come in.

Here's what I've got so far...
 

Attachments

  • IMG_1037.jpg
    IMG_1037.jpg
    580 KB · Views: 304
  • Frame and motor.jpg
    Frame and motor.jpg
    440.5 KB · Views: 311
  • motor.jpg
    motor.jpg
    483.4 KB · Views: 302
Re: CB450 First build- Dallas, TX: SUSPENSION QUESTION

Question about rear suspension...

Does anyone know the stock length of the rear shocks on the cb450's? I need to get some more clearance in the back end, so if i upgraded to 13" shocks would I have to make any changes to the swing arm?
 
12.5 " I do believe, least that's what mine measure. CB 360 swing arm fits with about 1.5" stretch (its 1.5 inches longer), just have to work over the slots for the axle, weights about 2 lbs less too.
 
frogman said:
12.5 " I do believe, least that's what mine measure. CB 360 swing arm fits with about 1.5" stretch (its 1.5 inches longer), just have to work over the slots for the axle, weights about 2 lbs less too.


Wow. Thanks for the info. Definitely something that I wanted to do, I just didn't know which swing arm would bolt on with minimal modifications.

So if I was to bolt up a cb360 swing arm, I would only need to drill out a bigger hole for the axle in the slots and possibly linkage for the brakes? Or would I need to close off the slots on the 360 swing arm so that its like the 450? and then I would need to run 13.5" or 14" suspension?

Sorry about all of the questions!
 
You can modify the slots with a hand file and drill the holes for the 360 chain tensioner larger to use the 450 axle. Can weld some barsock to the ends of the slots to close them up and use the 450 tensioners. OR you can run the entire 360 rear end. You will need the brake linkage and the brake stay from the 360 as well.

Shock mounts are about 2 1/4" further out on the 360 swinger compared to the 450 so longer shocks will be need to keep the height the same.

I happen to have both of the bikes, sitting beside each other so measuring is easy. ;D

Here's an example

http://indianapolisvintage.proboards.com/index.cgi?board=frame&action=print&thread=462
 
Oh nice! I need to finish this one and get a few more bikes in my arsenal haha

I just picked up a cb360 swing arm with the brake stay and chain adjusters on ebay for $40 shipped 8)

So when you were running the 360 swing arm on the 450, did you get longer suspension to raise the rear end? I see that guy used cb900f shocks. Those are like 15.25"

And Im assuming that its worth the money to spend the extra $30-40 on the better suspension rather than getting some japanese knock offs?
 
Yeah stock shocks are junk. Since you have to get new ones, pay the money get a good set. Wait till the swing arm shows up though, get it installed and then mock up the ride height you want and then measure for the shocks. Probably have to add an Inch or so to allow for compression when you sit on it.

Side note what did you do with all the old parts you took off like the stock tank and the fork ears/covers?
 
The tank actually had a big dent on the right side. I ended up selling the tank to a scrap yard guy for the cb350f tank in the top picture. The 350f tank had a smaller dent that I fixed with bondo. The ears I sold on ebay along with some other stuff.

But i do have a box of stock parts somewhere around my house I took off if you're looking for something specific i can check.
 
First Build CB450...99 problems and a petcock IS ONE!

Ive been buying parts like mad. Stainless Fasteners, Gasket set, cb360 swing arm, other misc stuff.... So I bought this tank on egay, It's from a '80 cx500. I've decided to try and make the bike a little bratty and this tank would do the trick. Im gonna strip the tank bare, do off white stripes down the middle and then clear coat the thing. Its gonna look sick...

I do have a question though...

cx500's had vacuum fed fuel systems instead of gravity fed like older cb's. Do you guys know how I can make this work with my cb450? anybody know of a gravity fed petcock that will fit a cx500 tank?

CX500 uses the 16mm petcock I believe...

KGrHqZHJBQE9qmdGl47BPdfHVrP-60_57.jpg
 
deepwaterimports said:
dude i like. im thinking my next project may have to be a big twin

Thanks man. You should do it. Big twins are the way to go man. Once im done with this i think ill do a GS or CB550 but that's a long way off haha
 
KGrHqVHJCUE9rPVHmYNBPdfHypYIQ60_57.jpg


Here is the underside of the tank. It looks like it fits just like a normal petcock would. Ive just never worked with a vacuum fed system and i figured i should get some extra opinion!
 
Re: First Build CB450...99 problems and a petcock IS ONE!

onehundredton said:
Ive been buying parts like mad. Stainless Fasteners, Gasket set, cb360 swing arm, other misc stuff.... So I bought this tank on egay, It's from a '80 cx500. I've decided to try and make the bike a little bratty and this tank would do the trick. Im gonna strip the tank bare, do off white stripes down the middle and then clear coat the thing. Its gonna look sick...

I do have a question though...

cx500's had vacuum fed fuel systems instead of gravity fed like older cb's. Do you guys know how I can make this work with my cb450? anybody know of a gravity fed petcock that will fit a cx500 tank?

CX500 uses the 16mm petcock I believe...

KGrHqZHJBQE9qmdGl47BPdfHVrP-60_57.jpg

Looks from the pic that the outlet is welded on. Occurs to me that most any petcock would work once you figured out how to mount it. asides from that, making sure there was a vent someplace so the tank wouldn't depressurize would be the only mod I can think of. Even something like DCC did on the Brass Cafe' (hard line to outside air) would work.
 
Back
Top Bottom