CB750c street rod build - "Old Blue"

NobNoc

New Member
Greetings all and thank you for viewing our first post! Since it is our first post, I'll preface it with a little history, we are a small start up shop in Denton, Texas specializing in Honda CB's. This bike is our fourth build, and we want to get involved with the CB750 community so I figured we'd start here! Enjoy the build, when the bike is finished it will be for sale!

1. Our build starts here, with a quite nice '81 CB750C with 21k miles on it. No real issues when the build began, ran smooth, pulled strong and stopped well, just some cosmetic issues and balding tires. The motor is in great shape, the timing is spot on and all cylinders blow a strong 175psi and all the valve clearances were well within spec, someone took good care of this bike.
IMG_0556.jpg


2. Right, so, didn't start taking pictures until about the end of day two, so they kick in after the bike has been stripped to the frame and had the swingarm removed. Old girl came apart super easy for us, even the usually bastardly soft Honda bolts kept up and we didn't have to extract any screws. We cut off the rear frame horns immediately after the engine hoop and all the trailings on the bottom after the engine hoop, we ain't go no time for all that metal.
IMG_0564.jpg

IMG_0586.jpg


3. Next up is a little mod that's just for aesthetics, I've done it to a few bikes and generally like it, but I take the headlight brackets, cut about an inch and a half or so off the bottom of each side, and turn em upside down and re-install em, you can turn em upside down and swap sides if you want to keep the pretty chrome side out. The end result is that the headlight sits about 4-6 inches lower on the front forks, which I quite care for, I like to see the road, not the ass of a headlight ;)
IMG_0567.jpg

IMG_0568.jpg


4. I love painting, the whole process. Sandblasted the tank and was amazed to find zero bondo, sanded, and primed. Remember! Paint is only as good as the primer under it! Light, even coats, HAND sand with 300 grit then 1500 after letting it totally dry, and don't let yourself think "it's only primer!"
IMG_0563.jpg


5. Silver bottom coat for a nice stripe. I have an air compressor and a paint gun/booth, but I've been finding myself painting with Duplicolor Perfect Match paint more and more. Sure, it's a rattle can, but it's great paint that sprays well, holds an impressive gloss and is hard to run. If you are doing stripes like I am, you :cussing:MUST:cussing: let it dry for AT LEAST 24 hours or you WILL be spending lots of extra time re-sanding and painting because your impatient plan of using painter's tape and pressing lightly will rip up the metal flake. Like mine did. Harrumph.
IMG_0566.jpg


6. Ol' blue gets a topcoat of dazzling blue, these pics seriously have no justice in em for how nice this blue turned out. Freaking Duplicolor, who knew? Got the stripe lined up and taped off. I like the rolls of vinyl pinstripe from Autozone, but silly teenagers, it's a stencil ;)
IMG_0593.jpg

IMG_0589.jpg


7. Next up while the tank dries overnight, the carbs get a rebuild and hand polish, plus our special NobNoc Screwectomy, as I like to call it, haha. No more shitty weak Honda screws, just hardened American grade 5! Woohoo!! Sorry no pics of the rebuild. It was late, had a few beers, memory wanes.
IMG_0643.jpg

IMG_0648.jpg


8. Most of the major frame work is done here. We fabricated brackets to relocate the shocks out of some nice 1/8" steel for the brackets on the top and bottom and built gusseted supports for the brackets for extra strength. For anyone whose curious, we're welding with a wire Hobart 190 amp 25% argon mix. Works wonders with Honda frames! Important to note, we're using the stock CB750 shocks here as a mock up ONLY!! You WILL need to buy stiffer shocks!
IMG_0655.jpg

IMG_0650.jpg


9. Tank's done! Turned out marvelous. Still need to buff and clearcoat.
IMG_0616.jpg

IMG_0618.jpg


10. Aaaand all in mockup. Coming together nicely.
IMG_0660.jpg

IMG_0663.jpg


That's about it for now. Stay tuned! We're not done yet... Next step, powdercoating!
 
Oh yes!

1. Good day today! Stripped the bike back down and welded two 3/4" steel tubes coming off the back of the frame with some nice gussets for strength. We're still debating on the seat. Either going to go with a bobber seat or custom fab a wood-leather seat.
IMG_0680.jpg


Now that that's all done, the frame, swingarm, engine mount brackets, triple tree, front fork holder, gauge cluster, handlebar fuse box, and handlebar holders are at the powder coater, they are going to sandblast the frame for us and shoot it with a special clear powdercoat, so it should all have a nice durable powdered metal look on the frame.

Stay tuned!
 
xb33bsa said:
your rear suspension you will need to rethink it
really nice paint tho !!!

Thank you!!

We didn't think the rear suspension would work either, but it does! The stock shock are NOT strong enough and we will be using some much stiffer shocks in the end but to keep it together around the shop it works pretty well. The stock shocks on the stiffest setting are strong enough for me at 275lbs jump on it full force and the back wheel doesn't contact, but with the motor on the frame it's too much and kinda holds but bottoms out.
 
you will still need to rethink it 12+" of rear wheel travel and the swinger cannot handle the load without major bracing
what spring rate have you calculated and where are you going to find shocks with stiff enough damping ?
what kind of chain tensioner system will you design ? you will need it
 
I hate to rain on your parade, but the rear end of that bike is a disaster looking for a place to happen. leaving aside the excessive travel, the forces are now trying to bend and break the swingarm, which they will do in time. It is not designed to take those forces the way you have it now.

As it stands it is lethal. Who designed that and worked out the forces involved?
 
xb33bsa said:
you will still need to rethink it 12+" of rear wheel travel and the swinger cannot handle the load without major bracing
what spring rate have you calculated and where are you going to find shocks with stiff enough damping ?
what kind of chain tensioner system will you design ? you will need it

We haven't finished the seat completely but the swingarm has about 13" of travel before it hits the seat, we are going to weld on some bumpstops and limit it to about 12" of travel. My math is rusty, but I calculated I'd need shocks with a spring rate around 1.4kg/mm with a fat rider (me), allowing for 20mm of sag, but I could be wrong. We are planning on buying a set of aftermarket shocks for a small ATV and using them, whichever suits our needs.

We're still puzzling the idea of a chain tensioner. I'm thinking of cutting up the chainguard and making it fit around the shocks and working a spring loaded cam timing chain tensioner from a small block chevy inside the chain guard.
 
I should also mention that if the stock swingarm doesn't work out, we are thinking of making ourselves another one out of studier metal.
 
NobNoc said:
I should also mention that if the stock swingarm doesn't work out, we are thinking of making ourselves another one out of studier metal.

It doesn't need "sturdier metal" it needs a new design that can deal with the forces involved appropriately.
 
Those gentlemen are correct,if you'd like some help with the design feel free to hit me up.
 
NobNoc said:
7.... plus our special NobNoc Screwectomy, as I like to call it, haha. No more shitty weak Honda screws, just hardened American grade 5! Woohoo!! Sorry no pics of the rebuild. It was late, had a few beers, memory wanes.
IMG_0643.jpg
You really swapped out all metric fasteners with USS SAE Grade 5's?
You do knnow they make quality metric fasteners...8.8, 10.9 or, 12.9
Pitty the next guy who has to figure out what the hell he is dealing with. ::)
 
Hoosier Daddy said:
You really swapped out all metric fasteners with USS SAE Grade 5's?
You do knnow they make quality metric fasteners...8.8, 10.9 or, 12.9
Pitty the next guy who has to figure out what the hell he is dealing with. ::)

Hahaha no, I used all the same metric screws. I said American grade 5 as a lame attempted pun. They're from Denton Bolt Co, it's a great local company and they can match pretty much any screw, nut or bolt you could possibly pull off a Honda (except the specialty ones like on the axle, etc)
 
the poor feller is not even aware that the extreme amount of wheel travel alone makes the bike an unride-able death trap
bump stops wont do any good when the swinger folds in half and unless he uses a dedicated short travel single shock with a spring rate to suit,the lack of damping in any conventiional set of dual shocks is going to pogo like a muther $%^&*()
i
 
xb33bsa said:
the poor feller is not even aware that the extreme amount of wheel travel alone makes the bike an unride-able death trap
bump stops wont do any good when the swinger folds in half and unless he uses a dedicated short travel single shock with a spring rate to suit,the lack of damping in any conventiional set of dual shocks is going to pogo like a muther $%^&*()
i

Yes, I am. We are NOT using the stock CB750 shocks, they are only being used for mockup and to get it around the shop, I thought I wrote that into the original post. I'm fully in agreement with you, right now it's a terrible terrible idea to ride it but we're not done with it. We're ordering stiffer shocks and if we don't feel comfortable with the strength of the swing arm when it's done we can always build a swingarm that is beefier or connects the shocks differently, or worst case scenario we'll just bob the bike like we originally intended and we've had nothing but fun experimenting with it.
 
xb33bsa said:
carry on it will look cool as fuk post video

Will do! And thank you for your input! I hope I don't come off as confrontational. This bike is more of an experiment to see if we can get this setup to work more than anything else, so the comments and critiques are welcome!
 
Back
Top Bottom