CL350 Project bike. I am going to need some help!

ChadLatta

New Member
Hey guys! I recently became the proud owner of two CL350's and a CB350. The problem (or exciting part?) is they are all in boxes.

So, I have a nice, titled frame for the 72 CL350 I plan to rebuild using all the parts to get the best possible bike. I am going for a Cafe style bike.

I started by tearing down the "good motor". By good I mean, it look the cleanest! As I tear it down I am noticing some wear. My best guess based on the mileage of the three instrument sets I have is that this motor was ran for 16,000 miles and then parked. The other two have maybe 3,000 or 4,000 on them, but look like crap on the outside. I breifly opened up the other CL350 motor (I have two CL and one CB) and the internals look a lot better.

My plan is to tear the clean motor completely and then replace parts with the better of the three parts I have....if that makes sense. I want to put together a strong reliable motor without investing a ton. I will buy what I need but if I can use better parts I already have I can save a little cash.

I guess I don't have too many questions at this point, but I will have a TON of questions here soon. By biggest concern is not knowing if a part is reusable or not, so I plan to post some photos as I go to get some tips and pointers from all of you.

There you go....my name is Chad BTW and I am really looking forward to getting my bike up and running!

Thanks

Chad
 
Hey chad welcome. Why are you tearing the motor down? Does it have bad compression? If not i wouldn't mess with it unless you plan on sporting it out a bit. I would personally just give it a tune up adjust the valves and check compression if it's above 150 on both cyllinders I'd just roll with it. I'd be willing to bet if the motor turned over and had oil in it It probably is pretty well fine in there. Besides you have alot of other work to do. Good luck man now lets see some pics. My bike was a basket amalgamation of 2 bikes/ 3 motors when i got it. It is really awesome to have that box o miscellaneous parts when you need something. Most guys have to resort to ebay and pay 10 bones for every little bit they are missing. I would pick the best of the engine covers though and be careful removing them those gaskets will prob need replaced.
 
Thanks.

I am tearing down the motor for two reasons. One, because I want to! Two, I never saw it run, it was "stuck" when I tried turning it over. I gave it a good heave and it let go.

After seeing the insides of this motor I doubt it would have ran, or at least not for long. The point area is rusted out, the cam tensioner is not in the best shape, there is at least 3-4mm of carbon build up all around! It needed to be tore down.

Also, the rockers are a little pitted, so I want to swap them with the non worn, non pitted set from the other motor. Cam chain, sprocket, etc all look good though. I will have to adress that when I get it out.

My goal really is to start from the first bolt and move on from there. I want to get into this motor and see how it all works, look over every bolt and call it my own. It was not a hard descision as the three motors where already off the bike. By "in boxes" I mean it was literally in boxes. Nothing was put together so I already had the bike in peices to start with.

I have three motors so I know I can use one for reference at least. I am really looking forward to the challenge.

Oh yeah, I have all new gaskets and bolts, etc. So I am all setup to put it back together when the time is right.
 
Really quick, I can post an image of the rockers I took out of the motor. I looked at the other rockers from the other CL motor and they look really good. I don't know if these look really bad, bad or just okay....anyway...

6b16c24a.jpg


0d238b47.jpg
 
Hi Chad, I will be interested to follow your project since I am working on a similar one also. Bought a 1971 CL 350 that I have torn down to the frame and will piece back together bit by bit as I clean up / replace / restore into a cafe racer style bike. Like yourself I want to rebuild the motor (which I am sure hasn't run in 20 years or more) to learn how and hopefully make it better than new when done. Good luck with your build!! Greg
 
Sweet. I will post my progress and ask my questions here as I go. I could always use as much support as possible!

I managed to get the stator rotor off today, after soaking the bolt in penetrating oil for 24 hours. I didn't come off easily, but its off. I am going to use the rear axle trick later to remove the rotor completely.

I do have two questions right now though. The cam chain looks to be in good shape. How do I check it? I have not looked at the manual yet, but are there specs or a way to check for stretch? Before I removed it, it was snug without any excessive play.

Also, the starter motor chain is loose. It turns and looks like it should work, but there is no tensioner. The chain will not fall off, but it does have more than a bit of slack. Is this normal?

Thanks
 
Back
Top Bottom