Clubman handlebars on CB350

Nortasaki

Active Member
I,m going to put on some clubman handlebars on my CB350. What have some of you done with the original switches and wiring ? Originally the wiring traveled inside the handlebars to the center behind the headlight. Any pics or info would be appreciated.
 
You can cut a slot into the control bodies to allow the wires to run on the outside of the bars. I was going to drill mine and run them internally, but it turns out my clubmans weren't entirely hollow.
 
I'm in the process of puttin some clubman bars on my CB550, and it's not as hard as it means. Just use a marker to mark where to cut. You can also use WD40 to allow the wires to slide in easy.... Good Luck
 
cutting holes and sliding wires...... :-X




or don't be an idiot and just notch your switch housings and run them externally, like honda started doing in the late 70's. Please don't do what my p.o and im sure others have done and START CUTTING WIRES.

Do it right, notch the housings and run them outside.



I'm relatively new but i swear it's always- "omg i gots teh cee bee now how does i put girl with dragon tattoo bars on omg old bars have wires inside them!@# too hards!"


also NO ONE HAS EVER ASKED THIS BEFORE
https://www.google.com/webhp?rlz=1C1CHFX_enUS476US476&sourceid=chrome-instant&ie=UTF-8&ion=1#hl=en&rlz=1C1CHFX_enUS476US476&q=+site:forums.sohc4.net+sohc4+clubman+wiring&sa=X&ei=WyevT9ueIMji2gW__fHpCA&ved=0CHMQrQIwAA&bav=on.2,or.r_gc.r_pw.r_cp.r_qf.,cf.osb&fp=356e729b7a15c7f0&ion=1&biw=1440&bih=809
 
whorobj said:
cutting holes and sliding wires...... :-X




or don't be an idiot and just notch your switch housings and run them externally, like honda started doing in the late 70's. Please don't do what my p.o and im sure others have done and START CUTTING WIRES.

Do it right, notch the housings and run them outside.



I'm relatively new but i swear it's always- "omg i gots teh cee bee now how does i put girl with dragon tattoo bars on omg old bars have wires inside them!@# too hards!"


also NO ONE HAS EVER ASKED THIS BEFORE
https://www.google.com/webhp?rlz=1C1CHFX_enUS476US476&sourceid=chrome-instant&ie=UTF-8&ion=1#hl=en&rlz=1C1CHFX_enUS476US476&q=+site:forums.sohc4.net+sohc4+clubman+wiring&sa=X&ei=WyevT9ueIMji2gW__fHpCA&ved=0CHMQrQIwAA&bav=on.2,or.r_gc.r_pw.r_cp.r_qf.,cf.osb&fp=356e729b7a15c7f0&ion=1&biw=1440&bih=809
wow take it easy bud guy just want suggestions how to make life easier. You are the only one who sounds like a douche.
 
Run them inside - lots cleaner, and there's no possibility of water getting into the hole you'll cut in the housings. You may have to use a washer with a fishing line tied onto it to get something threaded past the hard-angle bend in the clubman bars - then tie a solid-core wire to the fishing line and use it to draw the wire through, then use THAT wire to pull the wiring harness into place.
 
When I had clubman bars on my cb750 I ran the wiring internally and it looked nice. Take the time and do it right. Now when I put my clipons on I ran them externally because it would've only hidden like two inches of wire.
 
Yes swivel but when you're building a bike you take the time to do things that the manufacturer doesn't do. When I get done with something I take great pleasure in knowing it's done properly and as well as I could do it. That's just me though.
 
Personally never had a problem with reliability or safety. Worked fine. Never broke. Looked clean. I guess it's personal preference, but if your most important factors are safety and reliability then why not keep them all stock?
 
I'm more worried about moisture incursion into the switches, honestly... I've made the mistake of taking those things apart, and they're filled with mild steel springs and contact points, all of which are plenty rusted enough without actually carving holes into the housings. My bikes with external wires are indeed SIMPLER to swap bars on (extremely so) but they also seem to have more sealed-looking/solid state switch internals as well. I drilled mine, carved out the needed channels and even polished/smoothed all the edges in less than an hour...
 
Swivel said:
.....If you think the factories stopped doing it on bikes costing tens of thousands of dollars for cost or time concerns you are wrong.....

Sorry - but you're wrong because that's pretty much the main motivating factor in any production line - less time assembling is more profit.

Personally I don't like the idea of drilling holes in handlebars, but I've yet to see a pair actually break from having it done. A bit like people drilling top clamps on fighters to fit bar risers - everyone says it's dangerous, but I've yet to see someone pull an M8 bolt through 6mm of alloy ::)
 
Back
Top Bottom