DTT Mikuni Group Buy - January 2013

Sonreir

Oregon
DTT SUPPORTER
Hello again, everyone.

Been more than a few months since we've had one of these so I figured it's about time.

Format to follow the same as the other group buys: Please post IN THIS THREAD the type and number of carbs you wish to order. I will reply to this thread as the money is received, when the order with my supplier is placed, when I receive the carbs, and when I ship them out.

Costs for shipping within the US are included in the price, but please message me for shipping costs elsewhere (it usually comes to around $20 extra).

All payments need to be received on or before Jan 25th and delivery is expected in the first week of February (slightly longer for delivery outside the US).

As with the other group buys, all prices assume we manage to hit a $400 total (that's the amount I need to order to get a discount) and so if we don't reach it, prices will be slightly higher (buyers are free to withdraw their orders if this occurs).

Please feel free to ask any questions and I'll do my best to answer them. Also, though I've listed only the Mikuni VMs, I also have access to Keihin CRs and Mikuni TMs and I can get prices on those if you guys are interested (both the CRs and TMs are more expensive than the VMs, the CRs especially so).

All items will have two prices listed, the first price is for a single carb, the second price is for more than one.

VM26 - $90, $85
VM28 (round slide) - $100, $95
VM28 (flat slide) - $120, $115
VM30 - $90, $85
VM32/34 - $90, $85

Also... please note that all the carbs come pre-jetted from the factory for two stroke engines. Expect to spend another $15-$20 per carb for the brass you'll need to get these working their best on a four stroke. I can supply the series 176 needle jets for $12 each and a few assorted pilot/main jets for $8, please specify sizes). Many applications may also need new manifolds and/or throttle cables, but this will be on a case-by-case basis.
 
Hey Sonreir, I am interested in this for sure, but not right now, i've tied all my extra bike money up in a project resale bike.. Would you be up for running another group buy in March? I'd be purchasing ( hopefully ) 5 carbs total.. Let me know, I'd appreciate it..

Graham
 
Hi Sonreir,

See you again in this very popular topic. I plan to buy 2 VM30 shipped to Vietnam. Could you get me a quote (shipping as well). I preferred the following setup: needle jet P0/ Main jet 180/Pilot: 35
Many thanks
Viet
 
Very interested in a set for a kz400....not sure what I'd need for jets or size (I'm assuming vm30's would be the ticket but not sure) so any help would be appreciated there.
 
Hello I am interested in ordering a pair of vm 34mm roundslides for a 79 xs650. I am not sure what needle main jets are needed however the bike has no mods except for a pamco ignition an dual coil output. I have open pipes and that's it. So I need for you to tell me what configuration is needed that will work best for me. I can be contacted by phone at 951-833-4404 or email bigt951@gmail.com. The price includes shipping correct? I also need manifolds that will holds up the carbs without airbox support since its a custom bobber.

Thx
Tony
 
What would the price be for a bolt-on solution for my '73 CB350? I apologize for asking, but I'm not sure at this point what all I need. Thanks for any help!
 
I usually don't advertise the full kit because I don't think my prices are all that competitive.

I can do a full CB350 kit for $350. The kit includes the carbs (of course), two K&N air filters, and a two into one throttle cable. You may still need to source manifolds, but stock works for many bikes (I'm not 100% sure this includes the CB350).
 
Sonreir said:
I usually don't advertise the full kit because I don't think my prices are all that competitive.

I can do a full CB350 kit for $350. The kit includes the carbs (of course), two K&N air filters, and a two into one throttle cable. You may still need to source manifolds, but stock works for many bikes (I'm not 100% sure this includes the CB350).
I used a set of VM30 on my CB350 buy from Soneir. It runs great. The jetting is: Main: 180/ Needle jet P0 and pilot 35. I used velocity stack on my bike not air filter and a set of CB360 pistons.
Hope it works for Mattfeet
 
Sonreir said:
I usually don't advertise the full kit because I don't think my prices are all that competitive.

I can do a full CB350 kit for $350. The kit includes the carbs (of course), two K&N air filters, and a two into one throttle cable. You may still need to source manifolds, but stock works for many bikes (I'm not 100% sure this includes the CB350).

The VM30's will work fine on the CB350 stock manifolds but they do sell ones that are an exact match. If trying to install them on a CB450, you will need different manifolds.
 
Sonreir said:
Carbs have arrived this morning. They'll go out in this afternoon's mail.
Hi,
It is Viet. Have you got tracking number for my VM30 carbs.Thanks
Viet
 
Curious, are you able to pick up CR31 round slide carbs? for a CB900 which also fits the DOHC cb750's too. Any idea on the cost?
 
Keihin CRs? Yeah, I can get 'em but they're not cheap. I can get an exact price for you, but it's probably going to be around $750.
 
Back
Top Bottom