DWMS Racing CB450 Back To Basics Drag Pipes!

joeyputt

The green flag sets me free
I have been having a really hard time trying to decide how I want to build this motorcycle so instead of doing a stock restoration or building a full custom I thought I would get back to basics and build a nice clean low budget cafe and keep her as one of my personal motorcycles.

Here is a photo of the bike when I started.

000_0048.jpg


Here are a few photos of the engine work that I already completed.

48859-1.jpg


000_0065.jpg


000_0034_01-1.jpg


000_0048_00.jpg


I also started cleaning, painting, and polishing the rims and brakes.

000_0034.jpg


000_0041.jpg


000_0039.jpg


000_0059.jpg
 
Re: CB450

I removed the front end to replace the factory style ball bearings with new tapered style bearings and to replace the fork seals. I also started to cut the tabs off of the frame in the seat area and removed the rear hoop on the frame so that I can build the new tail section.

000_0058.jpg


I also cleaned and painted the triple trees while I had them off.

000_0065_00.jpg
 
Re: CB450

After the paint cured I installed the triple trees with the new bearings, the fork tubes with new seals, and the front wheel back on to the motorcycle.

000_0003.jpg


I removed the black paint from the handlebar clamps and installed them with a set of drag bars as I will be leaving the footpegs in their factory location.

000_0009.jpg
 
Re: CB450 Back to basics

Joe, I'm sure your "basic" build will be another piece of art. You do some fantastic work sir.

And I'm curious - what kind of paint is the gold?
 
Re: CB450 Back to basics

Big Rich said:
Joe, I'm sure your "basic" build will be another piece of art. You do some fantastic work sir.

And I'm curious - what kind of paint is the gold?

Thank you for the compliment Brother, the gold is VHT engine paint part number SP404.
 
Re: CB450 Back to basics

Very nice build. I like the use of gold as an accent color.
Have you tried test fitting the front master cylinder assembly yet? I was trying to use drag bars on my build and couldnt get the necessary clearance between the throttle and triple clamp.
 
Re: CB450 Back to basics

lstuckey1 said:
Very nice build. I like the use of gold as an accent color.
Have you tried test fitting the front master cylinder assembly yet? I was trying to use drag bars on my build and couldnt get the necessary clearance between the throttle and triple clamp.

Brother I installed the master cylinder today and there is enough clearance however it is close. The drag bars I am running have a little pullback to them so the angle of the bars creates more clearance between where the brake line bolts to the master cylinder and the handlebar clamp, if these bars were straight the master cylinder would not clear the handlebar clamp. I will take a photo tomorrow and post it here for you.

JustinLonghorn said:
I am onboard, sir.

Brother it is always good to have you here!
 
Re: CB450 Back to basics


So, basically 'just' another awesome build, eh? Liking this already! I have always been impressed with people who are able to pic accents like this. So clean man...watching, waiting!
 
Re: CB450 Back to basics

t71ford said:
So, basically 'just' another awesome build, eh? Liking this already! I have always been impressed with people who are able to pic accents like this. So clean man...watching, waiting!

Thank you for the compliment Brother, you are too kind and do beautiful work as well!

As far as basic goes I say that because I want to run most of the stock parts to keep the beautiful vintage look so I will be running the stock tank, air box, side covers, frame, rims, suspension, brakes, etc. The only parts that will not be stock are the tail section that I am building, a pair of cocktail shaker mufflers, and small parts like the handle bars, grips, head light, tail light, a braided front brake line, etc.

It has been a while since I built myself a motorcyle that shows off a lot of its natural vintage beauty instead of a full custom build.
 
Re: CB450 Back to basics

Wow. Love the direction this is going. Beautiful work so far, I will definitely be watching this one!!!
 
Re: CB450 Back to basics

Lookin' good Joey!
Sometimes it's the small changes that create the best looking bikes.
 
Re: CB450 Back to basics

Thank you for the compliments Brothers! As usual I have been very busy in the shop so there has not been a lot of time for me to work on my personal motorcycles however I did start to build the all steel tail section for my CB450. I welded the rear tank bracket to the front of the seat so it bolts to the frame at the front and welded studs in the seat pan at the rear of the seat so it bolts to the frame at the rear as well. I also designed the tail to have rubber mounts around the rear studs between the seat pan and frame to help with vibration.

Brother 4eyes I totally agree which is why I want to keep this bike really simple and clean looking!

I still have a lot of finish work to do but here is how the tail section looks on the motorcycle.

000_0009-2.jpg
 
Re: CB450 Back to basics

I love this thing, very nice work. The long pipes, the tail section, the 450....perfect.
 
Re: CB450 Back to basics

1976cb356 said:
I love this thing, very nice work. The long pipes, the tail section, the 450....perfect.

Thank you Brother! Your support means more to me than you know!
 
Re: CB450 Back to basics

Great stuff Joe! How have I missed this one??? Looks great. Love the colors and when it's done you'll definitely have a keeper!
 
Re: CB450 Back to basics

Deviant1 said:
Great stuff Joe! How have I missed this one??? Looks great. Love the colors and when it's done you'll definitely have a keeper!

Thank you Brother! Maybe I will have her finished soon and you can come for a visit to check her out!
 
Re: CB450 Back to basics

RoseCityCafePunk138 said:
I love me some 450 action. Killer build! I dig the drag bars instead of clubmans, nice choice!

Thank you Brother! She was going to get clubmans but I am going to leave the footpegs in the stock location so she sits really nice and feels really good with the drag bars!
 
Re: CB450 Back to basics

Nice. I want to go rearsets on my current 350 build but I'm debating customizing my fork sleeves to have some clip-ons. I want my forks to still look relatively stock but I want clubmans as well. If I clip 1-3/4" off between the top and the bottom, I can fit a pair on and powder coat them black to match the bike. Or I might just weld on a set onto the fork sleeves. Debates in my head!!!
 
Back
Top Bottom