Filter Pod, Anti-Pod, Steel Dragon Perfomance, that is the question

Hurco550

Keep er' Between the Ditches
DTT SUPPORTER
DTT BOTM WINNER
Another question for ya'll two wheel wizards out there. I am still plugging away at the cb550, and have decided to put filter pods on the carbs. Ok I am kidding, and all joking aside, this isn't meant to be a "bash filter pods and death to all who use them" thread. I have decided that I DO NOTwant to run pods. I know some have had luck with them and some haven't. Through some searching over on sohc 4 I found a setup called the Anti-Pod. A guy was having them made and selling them. He has since stopped having them made, and to get one you now have to more or less contact his distributors and get each component separately. I do not think I want to go down that road. I then found that Steel Dragon Performance makes a one piece air box that looks like it fits well with internal velocity stacks. I like the looks of the box and the idea of having all the carbs linked again by one air box, and not having to run the stock box. The price really isn't bad either at under 2 bills. (I know that's a lot but heck a GOOD set of pods can run you $100 anyways). My question is has anyone on here used the steel dragon setup and if so how do you rate it? Any input is great before I drop the cash! :)

Here is a link to steel dragon performance filters:
http://www.steeldragonperformance.com/air_boxes_7.html


And here is a link to the Anti-Pod setup from the sohc4 forum:
http://forums.sohc4.net/index.php?topic=79491.0
 
In my experience, CB550s are relatively easy to tune correctly with the right pods -- I've run pods and a Kerker 4-1 set up on my old 550 for 25+ years and it runs great. Doesn't do anything to answer your questions, however, but may allay your reticence to consider pods an option. Also, to continue to be unhelpful, I know nothing about the set-ups in your links, but continue to harbor suspicion about people who advertise "internal velocity stacks" -- especially considering that the stock airbox set up has what many call "internal velocity stacks," by which they mean to say the intake boots that join the airbox to the back of the carb and are shaped like a tube.
 
I have heard of people that have great luck with them and many are against them. Out of curiosity what pods are you running? I also know it depends on the specific pods you get. EMGO pods seem to be really bad from what some people say. I know "internal velocity stacks" is just a fancy term, but even on the stock air box, the way they are shaped does make a difference on how the air flows into the carbs. I appreciate the feedback and I am far from all out against pods, I just wanted to try this box out if some people had good luck with them.
 
hurco550 said:
I know "internal velocity stacks" is just a fancy term, but even on the stock air box, the way they are shaped does make a difference on how the air flows into the carbs.

This is true, but that still doesn't make them velocity stacks.

I should add that if you wanted to run a stock airbox there are usually plenty of people parting out CB550s or converting to pods to where it shouldn't be that expensive to pick up a stock unit. I parted out a 550 a few months ago and sold the stock airbox with boots for $40. I still have the air filter housing. Ebay has a bunch of stock set ups. And new filters for those things aren't that pricey.
 
I actually have the stock setup for mine as well. I just don't want to run it as I am working on a monoshock conversion and the box is in the way. I just like the look of not running the stock box. What brand of pods are you running on your 550?
 
Uni's. Can't remember the jetting, having opened up the carbs in awhile...

I should add: why do want to convert it to a monoshock? Two proper shocks in the back is the best set up for that bike...
 
I guess the easiest answer is I am a fabricator that cant leave well enough alone. I have read of people who have a lot of success with a monoshock performance wise and it is a challenge that I want to succeed at.
 
Well I don't have much use for a bike if I can't ride it. I know the rake and trail geometry to keep it safe, and not be be cocky, I'm an AWS certified welder with a background in machining and tool and die work, so building it right and sturdy shouldn't be a problem. If anything I over build stuff. I understand the concern, and I've seen the bikes that are built unsafe, but just because a few people have built un safe machines doesn't mean we all do.
 
Monoshocks, with a direct hookup, have no more performance that dual shocks. Because of the stiffening of the rear swingarm, they actually reduce performance due to greater unsprung weight. In addition, some extra steel is needed to increase the Frame strength. Adds more weight. To do it correctly, other parts of the frame may need to be stiffened to handle additional loads/forces in a direction and size they didn't have before. Finally, getting the correct damping and spring rate will be more than finding a spring that fits. Sometimes the factory even gets that wrong. Overdamped and undersprung, or oversprung, under damps, or all the other combinations.

Modern bikes using single shocks use complex linkages to create a rising rate spring response. To offset the weight, they often use aluminum alloy arms too. Without the linkages, a single shock is pretty much the same as dual, as far as performance goes.

I am O.K. with doing it because you want to do it, but from a performance point, it isn't really a change. It is mostly done for looks rather than real performance.

Just a reminder, that there is more to it than creating a single shock mount.
 
Whatt? I was just going to pull the shock off of the left side and call it a monoshock! lol I am kidding. I actually have two options going right now. One is a complete aluminum swingarm off of a Kawasaki ninja with the linkage type shock. That is what is mocked up under the bike right now, and of course the other is the one where you build the loop on the stock swing arm (i dont know what they are calling that). I understand what you are saying about un-sprung weight being added and all that fancy jazz. I have honestly done a ton of reading on the topic, but i get the whole "just because someone else did it wrong doesnt mean you have to do it wrong" thing. If I decide to do the modified stock swingarm method, I will more than likely run an aluminum rim to cut down on weight, and if i run the kawasaki swing arm I will run the Kawasaki aluminum wheel. I appreciate the input on the monoshock, and if you wanna see what i have going on here is the link to my 550:

http://www.dotheton.com/forum/index.php?topic=42259.msg463984#msg463984

but back to the topic at hand.. has anyone used the Steel Dragon Performance air box on their cb550?
 
bump. Anyone had experience with steel dragon performance filter boxes?
 
I'm waiting for mine but it's for a cb750 dohc so I will let you know how it goes once it gets here, and i get bike together
 
jaykim said:
I'm waiting for mine but it's for a cb750 dohc so I will let you know how it goes once it gets here, and i get bike together

That would be great man. I appreciate it.
 
I have one for my SOHC 750 but only had a chance to ride a couple of times before pulling the motor for the 836 build. I will say it is a QUALITY piece, albeit a little heavy. If you plan to run any of Steel Dragon's boxes I might recommend working out some type of strap or support. I ran without one a couple of times but really didn't feel comfortable doing so, as all the weight of the carbs and box is basically just suspended in midair, supported only by the intake tract.

Edit: Mine is the single breadbox style
 
coyote13 said:
I have one for my SOHC 750 but only had a chance to ride a couple of times before pulling the motor for the 836 build. I will say it is a QUALITY piece, albeit a little heavy. If you plan to run any of Steel Dragon's boxes I might recommend working out some type of strap or support. I ran without one a couple of times but really didn't feel comfortable doing so, as all the weight of the carbs and box is basically just suspended in midair, supported only by the intake tract.

Edit: Mine is the single breadbox style

The breadbox style is what I was looking at for mine. I was a little curious about that myself, the weight that is. I think I could figure out some kind of rubber mounted support. I am glad to hear that it is quality. That's something you cannot always see in pictures thanks for the reply
 
Just to clear something up here. Honda SOHC 4s have real velocity stacks inside the airbox looking just like a short rubber tube but the part inside the box is the right shape. We use CB750 inlet tubes on our CB160 and CB77 race bikes and CB500 shorties on a very high revving CB175 based race motor.
 
teazer said:
Just to clear something up here. Honda SOHC 4s have real velocity stacks inside the airbox looking just like a short rubber tube but the part inside the box is the right shape. We use CB750 inlet tubes on our CB160 and CB77 race bikes and CB500 shorties on a very high revving CB175 based race motor.

that's what I thought I had read, and I knew when taking it apart that it was more than just a rubber tube to connect the box to the carbs. One of the other reasons that these boxes seemed like a better option than pods to me at least...
 
inside peek- CB750 plenum side of airbox:
 

Attachments

  • DSCN9625.jpg
    DSCN9625.jpg
    32.8 KB · Views: 2,396
Indeed, the stock box is incredibly well engineered. If I had bought my 750 with a stock box it would have been left alone entirely. However, it did not, so I got to play filter mix and match, much like you are now.
 
Back
Top Bottom