First Cafe project (CB450)

Hoosier, thanks again for the great info! One thing though, I'm confused with terminal 85/86. When one is grounded, is the other the return from the main feed? Excuse my ignorance but, any way you can explain that to me in the simple form? Haha.
For example if I'm using the black wire to feed the coils, headlight, taillight, and neutral light, how exactly is the relay placed here? I understand using 87 from the relay to feed all those, but where does 85/86 come in play? I understand it's the trigger switch, but what feed triggers it? Also, do I need to use 14g for the main feed across the bike? Or can I go to 18/20g after the relay?

Thanks in advance!
 
Do you guys know if I can dump this part (the piston) of the carb in the boiling lemon juice as well? Or will that damage the piston?
 

Attachments

  • photo-3.JPG
    photo-3.JPG
    518.5 KB · Views: 305
Just did a compression test, and got 155psi for each cylinder. Engine is dead cold of course. That should be good?
 
Looks great.

Be careful putting the wheels on and off on that "stand". Mine fell over on my dad when I took my rear wheel off during reassembly.
 
Doc. said:
Just did a compression test, and got 155psi for each cylinder. Engine is dead cold of course. That should be good?

Yup. That'll do. Test it again once you have everything running though.
 
Flugtechnik said:
Looks great.

Be careful putting the wheels on and off on that "stand". Mine fell over on my dad when I took my rear wheel off during reassembly.
Haha yeah I'm aware, I had long 2x4 under the neck when installing the front wheel. I have the front wheel on now, just have the rear wheel sitting on the rear hoop until I get the wheel spacers from the powder coater :P.

Sonreir said:
Yup. That'll do. Test it again once you have everything running though.
I wish you had posted this two days ago. People kept telling me I need to have the 163psi minimum, but I guess they didn't know it was a new cylinder/rings. I was super upset that I had to tear it down again, haha. I then did a google search and read in many places that the rings need to seat. So I'm just hoping that will cure it.
 
You guys have any tips on cleaning the vacuum piston posted above? Any strong chemicals that'll clean that up, and not ruin the piston?

Also, if I decide to get a set of Mikuni VM30s, will the stock boots fit on those, or do I need to get the Mikuni ones?
 
I have vm32s on stock XS boots fit was fine . You should be able to find the size of the motor side of the carb and the size of the stock boot to see if they match .
 
Doc. said:
Do you guys know if I can dump this part (the piston) of the carb in the boiling lemon juice as well? Or will that damage the piston?

No problem - drop it in. I sure hope that the outer surface of the piston looks better...
 
DreadRock said:
I have vm32s on stock XS boots fit was fine . You should be able to find the size of the motor side of the carb and the size of the stock boot to see if they match .
Yeah hopefully I can find diameters.

Rich Ard said:
No problem - drop it in. I sure hope that the outer surface of the piston looks better...
The actual tube part that slides inside the other tube (actual piston I guess?) is perfectly fine. It slides fine and creates pressure. It's just what you see in the pic. I just wasn't sure if the lemon juice will eat up the smoothness of the piston.
 
What I circled in red, 1 that slides inside 2, is in perfect condition, and is what I'm worried that will get ruined by the lemon juice. All the corrosion is the areas pointed with the green, which is pretty obvious, haha.
 

Attachments

  • photo-3[1].JPG
    photo-3[1].JPG
    467.9 KB · Views: 283
The outter diameter of the piston and the bore of the cap that you have the green on have to be smooth as well. That seal is what allows the piston to raise and lower by the vacuum. Such tight tolerances they are a matched pair. You can clean the bore and piston with cheap aluminum foil. I wad it up and straighten it out a couple times first to wrinkle it up.
Leomon juice will be fine, and should help loosen the corrosion first.
 
HD, is there a reason you can't just use triple or quadruple #0 Steel wool (#000 or #0000)? Just wondering why aluminum foil, other than it's aluminum on aluminum. <<--did that even make sense?
 
Hoosier Daddy said:
The outter diameter of the piston and the bore of the cap that you have the green on have to be smooth as well. That seal is what allows the piston to raise and lower by the vacuum. Such tight tolerances they are a matched pair. You can clean the bore and piston with cheap aluminum foil. I wad it up and straighten it out a couple times first to wrinkle it up.
Leomon juice will be fine, and should help loosen the corrosion first.
I'll try to take better pics of the piston and the bore, but they really are clean (from what I remember). I think it's just the lighting that makes the bore look dirty. It travels up and down smoothly and creates suction, it just gets hung up on the outer corrosion sometimes. I'll boil it up first and see how much of the corrosion comes off, and check to make sure the piston and bore make a good seal. I'm just afraid the lemon juice will leave some type of oxidization layer on the pistons and bore from the surround metal. But I will be dipping it in baking soda and water afterwards, so hopefully that'll help clean it up.
 
Oh and how would you use aluminum foil on the bore? Just stuff it in there and spin it around?
 
Quick question... When you put your new suspension on the rear, did you have to make any modifications to the swing arm? Im about to buy longer suspension for my cb450 (im trying to get about an inch of lift in the back) and Ive seen a few people who had to make modifications to their swing arm.
 
Back
Top Bottom