Hondazuki XLRM250 Trans-America Hell Ride

Much thanks, fellas.

I'm leading into that fairing with and idea I have for a couple of LEDs I originally bought for the 175. I spent the better part of the day machining a couple of bezels. I went with steel because I went into this with the intention of flattening one side and welding the together. That may not happen anymore.

811512b464a2c446307c6b378aa56d7c.jpg



Sent from my iPhone using DO THE TON
 
Cross eyed! LOL. that looks pretty neat. Can they be independently aimed so you can spread out the light?
 
Maritime said:
Cross eyed! LOL. that looks pretty neat. Can they be independently aimed so you can spread out the light?
They'll extremely bright, even on 6v power, and they have a projector lens, so the spread per light is very wide. The plan is one lamp for low beam and two lamps for hi beam. I ran these on my XL175, so I'm familiar with the brightness and spread.
 
Not all carbs fit inside the frame... this is bootyfull :-*

s-l1600.jpg


But... if you try sometimes you just might find

s-l1600.jpg
 
Tune-A-Fish said:
But... if you try sometimes you just might find

s-l1600.jpg
I visited this possibility, but the monoshock prevents it. I thought of a more angled intake and a pancake filter, too. That may still happen, but for now I'm very happy with the current rig. A hi pipe would've taken the same space, so the carb rig will ride just above it. I'm really not sure how 1.5" wider is a big deal anyway.
 
e5f736e62f4fbf8c671419f7f2310d85.jpg


Exhaust from CB750 pipes, XL175 header, and KX can. We'll cut hangers off the can for final install.


Sent from my iPhone using DO THE TON
 
Still getting small bits installed on the XLRM- clutch, cables, etc. Working on the front fairing and hoping to have fire by Thursday...

Also prepping this guy for the coming weekend. The tank was completely caved in, the spark plug hole threads stripped and filled with JB weld. Misrouted cables were crushed, no front brakes, etc. As soon as the Red-kote fully cures, we'll dump gas in it and take it for a ride...

13138938_10209491425911843_8222133543720397567_n.jpg
 
deviant said:
Still getting small bits installed on the XLRM- clutch, cables, etc. Working on the front fairing and hoping to have fire by Thursday...

Also prepping this guy for the coming weekend. The tank was completely caved in, the spark plug hole threads stripped and filled with JB weld. Misrouted cables were crushed, no front brakes, etc. As soon as the Red-kote fully cures, we'll dump gas in it and take it for a ride...

13138938_10209491425911843_8222133543720397567_n.jpg
Yeah! Get it son!
 
If you've ever had a 1977/1978 SOHC CB750, then you're probably somewhat familiar with the carb I put on this bike.

e66e166b54b87aec8ff4cad72206aa4e.jpg


It's a Keihin PD carb without a lot of literature. It's was hell cleaning all the circuits, particularly the accelerator pump circuit which has 2 ball valves.

1919bc2c6ee02815087060656f7fd3d9.jpg

e36613465a0491af6f8502d422887999.jpg


And a second bladder for air...

97699d3a8fbab4f704a13fe3cb8d408d.jpg


After a dozen or so disassembles, I finally have ignition and idle.

http://youtu.be/q8sKyk8MoBo

I still need to wire the bike up, add the chain and decide whether to run battery.



Sent from my iPhone using DO THE TON
 
good work :D
but here i go again the tube on aircleaner side looks too restrictive at the small diameter it is and length
you need to do get it out and see if it will handle wot under loads
just went thru the same situation i mean almost exactly but x2 crabs a cx500... friend of mine let em use the shop
he had very similar proportins on the tube it would not rev out under any kind of load as soon as he clamped the uni foams on short velocity type funnelers it spunked up proper like
just sayin time to test it with a load and my fingers crossed for ya
 
Back
Top Bottom