Hondazuki XLRM250 Trans-America Hell Ride

xb33bsa said:
good work :D
but here i go again the tube on aircleaner side looks too restrictive at the small diameter it is and length
you need to do get it out and see if it will handle wot under loads
just went thru the same situation i mean almost exactly but x2 crabs a cx500... friend of mine let em use the shop
he had very similar proportins on the tube it would not rev out under any kind of load as soon as he clamped the uni foams on short velocity type funnelers it spunked up proper like
just sayin time to test it with a load and my fingers crossed for ya
Thanks. No disagreements on assessment. My hope is there is enough volume. In kilns, when you're stuck with a building that's fitted with 1/2" line, you install a length of 1 1/2" pipe to increase volume at the unit. Pressure remains the same, but the chamber gives it enough fuel to pull from. We will see.
 
I think I just realized what you are seeing. The interior of the tube is the same dimension as the mouth of the carb. The extra on the collar is machined to accept a set screw, so it doesn't constrict until all the way at the end, which is where the XL175 part starts. So I have a length of about 160mm of unrestricted tube. I'm not saying definitively that this will be without issues. Testing must happen. But, I'm not sure it's as constricted as you assume. That's were my description of the kiln design comes in...
 
Just add a reed valve in the tube that opens WFO allowing cool outside air in then green zip tie a chunk of UNI foam over it for dirt n such... redneck NOS a can of computer cleaner to the reed for a hundy shot when you need to pull the boat out the lake :o :o
 
a straight tube is a restriction the longer it is the worse it is,thats all
you only have the pressure diferential working for you its not like the engine is pulling in air,its not like it can reach out ad grab air and drag in
na engines rely in part on the energy the air can gather up in kinectic energy to make its way to the valve
you do see straight tubing on bmw airheads and the earlier ones were pretty small tube dia
as the years went on and they developed more power,more rpm those tubes had to grow in diameter and they did
you got a hipo engine that thrives on revs you cant scoot on a 250 single withjout rpm's
it might run perfect down low and in the middle but wot, the upper ranges, you got a restriction, the motor wont be getting as much air as it would if it was a normal config how much or how bad only testing can tell
 
This build is awesome man. I love to see frankenstein bikes...way out of my league for engineering skill but learned lots nonetheless. Looking forward to the 'final' product.

Getting some inspiration for the XL build myself here :o

Where are those lights from? Running them on 6v I assume? Really dig the number plate/front fairing on this and the 175.
 
adventurco said:
This build is awesome man. I love to see frankenstein bikes...way out of my league for engineering skill but learned lots nonetheless. Looking forward to the 'final' product.

Getting some inspiration for the XL build myself here :o

Where are those lights from? Running them on 6v I assume? Really dig the number plate/front fairing on this and the 175.
Thanks a lot, man.

I got the lights a couple of years ago on eBay for $30/pair. I'm not seeing them there anymore, but they're on Amazon for double...

http://www.amazon.com/White-Lights-Fender-Lighting-Aluminum/dp/B00F8JS2D0

I do run them off of 6v. They say they can run between 9v and 14v, but I ran them on 6v on the 175. Since the 250 has a separate lighting coil, I'll run a 12v reg to push power to the lights. Those rock lights are bright as hell at 6v or 12v.
 
I took it on it's first spin in the yard. I tried to wheelie it, but I couldn't get grip on the wet grass. I think I need to find a better 19in dual sport rear tire. They're not very common. I also need to get the kick stand fabbed up. I almost dropped it trying to stop the recording. ;D ...

https://youtu.be/SegiX_KA2FU
 
deviant said:
I took it on it's first spin in the yard. I tried to wheelie it, but I couldn't get grip on the wet grass. I think I need to find a better 19in dual sport rear tire. They're not very common. I also need to get the kick stand fabbed up. I almost dropped it trying to stop the recording. ;D ...

https://youtu.be/SegiX_KA2FU


SWEET
 
I guess it's time to reveal why I built this bike and why the carb setup is the way it is...

https://youtu.be/HBTZtYofcs4

Pay close attention the 40 second mark. You'll see the jump and then return after a year of travel.
 
xb33bsa said:
that was bitchen good work
40 seconds wha happen ?
Thanks. Did you see me disappear into thin air? Not totally sure how. I guess the computer couldn't handle the breakneck speed of the bike, so the camera lost me. You can kinda hear the sound of the bike still. I only rode for another 50 yards or so before I turned around to shut the camera off.
 
71a6ba905c11b2c5e860990f88539c89.jpg



Sent from my iPhone using DO THE TON
 
Awesome. Grats on first ride.

I really dig that headlight setup. Are they adjustable so you can aim them properly? Or fixed?
 
adventurco said:
Awesome. Grats on first ride.

I really dig that headlight setup. Are they adjustable so you can aim them properly? Or fixed?
Thanks. They're adjustable. I fabbed a mounting bracket with 3 adjustment points for up/down left and right.


Sent from my iPhone using DO THE TON
 
Back
Top Bottom