Is this an amazing find? NORTON!

Crusader said:
Noted..lol. That made my decision way easier. Just watched an Amal carb rebuild on youtube. I'm hoping I can just clean them up, replace the spark plugs, jump it, and be good to go (with the exception of tuning). One of the petcocks on the tank needs to be put in but luckily one of the boxes of parts has a couple of brand new ones in there. I did notice some light rusting inside the tank. I've seen worse. At the risk of sounding stupid, what should I do? Obviously that should be cleaned first (right?).

This is a question I ask myself all the time and especially when I stop for a pick up on a bike, mini, ATV, etc. If the guy/gal has an obvious level of mechanical knowledge based on the other power sports, motorcycles, projects laying around like that person does in their garage. IF a "tune up" is all it needed wouldn't he have done that and sold it for an easy 1.5x more? Maybe no on a 1972 cb350, most likely yes on a commando... Just my opinion. It always makes it a tougher decision when you buy a bike from a "mechanic", even a garage mechanic, that can't or choose not to get a bike running before they sell it.
 
Crusader said:
Thanks for the advice guys. You have instilled a little more confidence in me to pull the trigger. I was planning on shooting for around 4k. I hope theres some people here that know how to work on Nortons!

And for everyone that thinks Im going to cut it up, rest assured the only thing I would do is make a seat pan that mounts up to the current mount points (so I can reattach the original seats) and put a more cafe seat on it. Maybe some clubman bars..and presto, sexy bike. Being able to go back to the original look will be a snap (and equally as sexy).

Edit: *noob question* what are fork emulators.

norton_1t.jpg


Corbin Gunfighter seat, clean it up & ride, or find the "Fastback" seat he probably has with his extra parts.

Check the exhaust stubs. After awhile the pipes will "walk" off the ends of them, and/or the threads will strip in the head. There's a couple fixes for it.

Ditch the AMAL carb (and by that I mean clean & box it for resale) & buy the Mikuni conversion kit. It'll run easier...when it runs :)

There is a trick to kickstarting them. You'll want to learn it or you'll wear your leg out.

They're amazing to ride,. Price is high IMHO but prices have been going crazy lately, so if you can afford it *and want it* go for it.

-=Tom
 
As I mentioned my brother's (750 Commando 1972) was fussy to start until he put a Mikuni and Boyer ignition on it then it became simple/normal. Race Tech fork emulators are a very clever valving device that fit inside the fork tubes that change old style damper rod forks (your Norton) to emulate the action modern cartridge forks. They work very well and don't cost too awful much. We've used them on Triumph Thruxton, Yamaha FZR 600, Suzuki GT750, and will use them on an up-coming Aermacchi 250. I would quiz the owner about everything. Best of luck.
Cheers, 50gary
EMULATORGV - Race Tech Suspension
 
SONICJK said:
Buy it, slap some clubmans and dcc rearsets on it.
Dont forget to wrap the pipes too.

And don't forget the surfboard.

http://www.bikeexif.com/surfboard-motorcycle
 
hillsy said:
If you can AFFORD to throw $4k at a non running bike with the worst case scenario that the engine is shot.....then go ahead.
Doesn't sound like it though.....Caveat Emptor.....

I have to agree with this. This bike has likely been given up on and is relying on a naive buyer. They can be money pits, and you require a voodoo shaman to understand the nuances of these bikes.
Besides, it can't be a real Norton, I don't see a puddle of oil under the engine.

Rare and good are two different things. 20 years from now, Hyosung 250s will be rare.
 
Haha it can't be a real norton there isn't checkered flag ace cafe stickers on it

Or it can't be a real norton there isn't a tattooed twenty something dressed like 1950 riding it
 
caferay said:
Rare and good are two different things. 20 years from now, Hyosung 250s will be rare.

A "running" one is rare enough now.

Hell, I can probably still change the engine in the GT250R blindfolded....

-=Tom
 
It's a simple twin cylinder push rod motor. There's nothing magical about working on them. Threads are weird, exhausts tend to strip out, cranks go, main bearings fail valves stick and it's all easy to fix. The only mystical thing is setting up the isolastic engine mounts. The rest is pretty simple. A buddy of mine brought one over a couple of years back with stuck valves. Ethanol in the fuel leached resin out of the fiberglass tank and that coated valves in a sticky mess and one or two ended up bent.

Took all of a couple of days to strip and clean it all up and pop in new valves. really simple design. In fact the Norton twin was designed back in the late 40s early 50s.

There are Norton guys all over the US and lots more in the UK and Australia. They didn't sell as many as Mr Honda and there are a lot less around than CB350s, but they are just a bike. Fun to ride, and great to own, but still just just a bike.
 
My dad has (and always had) several Nortons and he and I slowly restoring a 65' Atlas. Teazer is correct, there is nothing magical about them. I'd agree that a Mikuni and electronic ignition are a damn fine upgrade. Parts can be found, they still have a very loyal following throughout the US and yes, parts can be a bit more pricey than for hondas but what isn't?


I've ridden my dad's P11 Norton from time to time and I'll say that I'd take it over a vintage honda anyday.


So, unless the engine is shot, my opinion is that you are looking at a sweet(enough) deal.


Don't forget your Whitworth wrenches.
 
Whitworth or BSF - and that stands for British Standard Fine BTW. Much as I'd like to say that means it's all fine. It really means fine pitch threads. BSC (coarse) was basically replaced by Whitworth. In the UK and other civilized countries (snigger) BSF/Whit tools are easily available. Less available in the US but they can be obtained.

You may also find BA threads in small parts like the points plate and possibly a few metric threads.
 
Ok, I am no expert by any means. BUT, my dad happens to own a 1973 Norton 850 Commando. Beautiful bike and a lot of fun to ride. However, they can be pricey to repair. IF the isolastics are shot, you are looking at over a grand to repair them. My dad's mechanic is a pro when it comes to British bikes and he did his for about 1500; if I recall correctly. It is a royal pain in the ass job to do (no pun intended). They go with age if you let the bike sit or if you ride the tits off of it. Additionally, that seems like a pretty low price for the bike in general. Typically I have seen them go for 6-10 in good condition; which that one looks to be. Once the bike is running 100%, or close (British bikes don't seem to run 100% - ever.) you will be more than happy. If you do get it, don't be alarmed when the entire bike shakes like a Harley when you decelerate to a stop sign/light. Everything is rubber mounted :)
 
teazer said:
Whitworth or BSF - and that stands for British Standard Fine BTW. Much as I'd like to say that means it's all fine. It really means fine pitch threads. BSC (coarse) was basically replaced by Whitworth. In the UK and other civilized countries (snigger) BSF/Whit tools are easily available. Less available in the US but they can be obtained.

You may also find BA threads in small parts like the points plate and possibly a few metric threads.

You may also have some threads that are cycle thread, although I don't know if they were still using cycle thread at the time this bike was built.

Imho, I wouldn't buy that bike unless it was running, well not for that sort of money anyway. I bought a T120 about 5 years ago which was running for $2500 which wasn't a bad deal. Took the engine apart to check it all out and I have never seen so many stripped threads and butchery in an engine so even if she runs it's no guarantee that it doesn't need a lot of dough spent on it. If you can get it for the right price no problem.
 
Man...It just keeps sounding riskier and more difficult. On one hand I have everyone telling me to buy it and on the other I have people telling me a million little things could be wrong with it and I could be flushing money down the toilet. This could be the most expensive gamble of my life! I'm starting to think the price is a little high for a non running commando. I've seen some in similar condition in non running form for about 2k less. But then again it comes with a surplus of extra parts.
 
Crusader said:
Its in a box next to it...threads are good on the nut thing (don't know the name of it) on the head. Might just be missing the mounting bracket, no big deal.

I'm liking this seat. It comes with a rep pan that mounts up using the same knurl nob mounts as the standard seat...so no mod needed. I wouldn't mind throwing a Dunstall tank on it.

http://www.motorcycleseatsdirect.com/norton-commando-750-850-interstate-cafe-racer-motorcycle-seat-unit/

A few simple mods and I could be rolling on something similar to this:


1962 Triton by Jon Barbour, on Flickr

Only part in common between those two bikes looks to be the rear hub. Commando frames are very different to a featherbed - can't weigh any more though.....

If it runs and it's in great condition it's probably worth that asking price. It's more than I would pay, but I'm cheap.
 
Back
Top Bottom