Jetting on CB200 with cone filters and no mufflers

InstantKarma

New Member
Hey guys,


Ive got a CB200 that I just finally got running (sort of)


The idle seems to be all over the place. It will run almost normal for a few seconds, then jump way up... then back down... over and over.


The previous owner put some simple cone filters on it and also cut off the mufflers. So right now the exhaust ends right at about where the brake/shifters are on each side.


I see that the stock jet sizes for this bike were 88 main and 38 slow. Right now the bike has 97.5 and 39. I feel like this might not be nearly high enough for the open exhaust. Just hoping some of the experts could shed some light.


I also thought it may be a vacuum leak (or leaks) but its hard to test with the starter fluid method because the idle is already jumping all over.


Thanks for any advice!


-Brett


Heres a picture for fun
4k2gT.jpg
 
Needs longer pipes
Stock are dual skin, inner pipe is pretty tiny
Have you cleaned carbs and checked float level?
Cleaned and re-set points gap?
re-set ignition timing?
Fix any air leaks at manifold (intake and exhaust)
 
What pods are you running? those cheap emgos are junk and with those pipes will almost never run as it should, so you need to figure out what you are willing to deal with. either way i would actually expect to make less power with those mods then stock.
if the idle is all over i would bet it has an air leak.
have you checked the manifolds for cracks? are they hard and not sealing well?
88-97.5 sounds like a large jump....
how many jets do you have? i would think you need a lot of sets to figure things out.
Yes the internet can help but its not going to be "buy X" and go. you will have to get a few closer sets to tune


corrado?
 
I cleaned the carbs really well over the last few days. The floats are set at 21mm on each carb (which is what the manual says it should be). It runs way better than it did before. It would only run on one cylinder before I cleaned the carbs.


I have not checked the points yet... I'll check on that tomorrow. No cracks in the manifolds... but the O rings should most likely be replaced... they are pretty stiff.


I'll probly start searching for a CL exhaust as well


and yeah its a 90 G60 corrado :)
baycheck2.jpg

baycheck3.jpg
 
Corrado is one of my all time favs.
Up there with the s15 240sx and mr2 turbo.

Sent from my HTC Glacier using Tapatalk
 
update


I replaced the O rings on the carbs and the manifolds. I also went ahead and put a couple 88 (actually 87.5, closest thing I could find) main jets in. The idle is much better but still touchy.


It will idle just fine for about 10 seconds with full choke, then as the motor warms up it starts to climb slightly but eventually evens out again. If i touch the choke even the smallest bit the idle jumps way up and doesn't come back down. the choke might as well be the throttle...


The air mixture screw is 1 and 1/4 turn out from seated, and the smaller fuel mixture screw is also 1 and 1/4 turn out from seated. I have tried playing with them both a bit but they don't seem to change anything.


I did notice that the rubber tube between the carb and the cone filter pods have some small cracks in them... could that cause this much of an issue?


Or is the fact that I have open exhausts causing the racing idle?


I am in the process of getting a feeler gauge right now so that I can check the gaps on the points and the tappets.


Thanks again
 
the gap on the points is prefect. right at about 0.4mm or roughly .015in


my gap tool doesn't go small enough for the tappets... im not sure why those need to be checked anyway?
 
Because they do. ::)
Get a set of standard feeler guages, about $1.99 in Harbor Freight or Wal-Mart
use 0.002" intake and 0.003" exhaust
The process is covered all over this site, 200 is just a smaller version of CB350 when it comes to servicing
 
Get some mufflers first to get it to run right. It will have trouble running well with just header pipes and it will also get you a noise ticket or at least attract all the wrong sort of attention.

Stock jets are a good place to start. Those carbs have two screws each. One adjusts the amount of air going to the pilot jet and the other props open the slides and acts like opening the throttle. Try to adjust them so they just touch the slides and then screw them in say 1 turn more to lift the slides slightly and move from there.

Cheap pod filters really are a PIA even on those simple motors, but that's what you have so let's see if we can get you into the ball park. Good to see you fitted the rear fender . Smart move.

The tappets should be checked as should points gap and ignition timing to get the bike to run at its best.
 
Thanks ;D


the list of "to do"s for tomorrow include getting a better set of gap feelers to check the tappets, getting some more fresh gas in the tank, checking the timing, and putting the stock air boxes back in place. (hopefully all the parts are still in the boxes the PO gave me)


still working on a solution for exhaust......... I have the stock mufflers but they have some rust holes and would need to be welded or clamped in some fashion
 
I checked the timing. looks like it was off by a few mm. not a lot but it for sure needed a slight adjustment. (my test light turns on slightly before reaching the F mark on the crank)


I checked the tappets as well. I an fit .002 in both side (intake and exhaust) I can fit the .003 in the exhaust pretty nicely... I can fit the .003 in the intake side as well but it can feel that it is more snug on that one so I think the clearances are good.


The part that sucks about having open exhausts is that I have to wait for my wife to wake up before starting it up ::)
 
ok so it runs way better now after setting the timing and adjusting the points a tiny bit. It will at least stay running on its own for several minutes without me having to constantly play with the throttle or choke.


There is still something very wrong though... The idle still just kind of rolls up and down between 1000 and 3500 with full choke. If you take the choke off even the slightest bit the idle races way up. I tried riding it a couple hundred feet down the street with the choke completely on, the throttle does just about nothing. the choke on the other hand makes a great throttle...


I made sure the slides in the carbs were sliding and rebounding correctly. We put fresh as in it... tried running it with no air filters for the heck of it...


not sure what else to try now (other than putting more of an exhaust on...)


what else could cause symptoms like this? the rpms of the engine shoot up and out of control when the choke is off even a little... im stumped... would low compression cause this kind of behavior? I had about 130 on one cylinder and about 120 (this was doing the compression test cold and with using only the kick starter)


Thanks guys
 
You do have the slides in carbs the right way around?
The cut-away goes towards the air filter side.
Also, (as I can't remember) are the slides left and right handed? (I know Mikuni's on Yamaha two strokes are ;) )
 
Yep, the slides are in there the right way... I double checked that last night as well. I checked that the slides are also bottoming out as far as possible in the carb. I thought maybe one or both of them were getting hung up and sticking half way open or something.


and yeah, the cut out on the side of the slide that the idle screw sits inside of is side dependent. It wouldn't even be possible to get the slide into the carb on the wrong side unless you had the idle screw completely out.
 
Up and down idle with choke is because it's too rich and normal (although it should be so rich when warmed up it should cut out)
Your going to have to check for air leaks in manifolds.
I think I have a set of 200 carbs here somewhere, I'll see if I can find them so I know what I'm looking at (probably same place as cam caps I'm looking for for Teazer ::) )
 
cool thanks... I really appreciate the help


I'll take some close up shots of everything tonight just for reference. I'm a bit of a noob so maybe there is something you guys can spot that I am just overlooking
 
have you checked for intake leaks again?
Have you gone though the factory manual on how to tune?
it has a good right up. its important to do things in a certain order
 
I had a suspicion that the 2 screws that go into the intake manifolds could have been leaking so I put some rtv on them and threaded them back in nice and tight.


The idle is a lot more stable now... it doesn't just jump all over. its calm enough now that I started it up and was able to play with the idle and fuel screws enough to where I could actually hear them make a difference. I was also able to get it to run with the choke wide open without redlining. It is still a high idle but not 10k rpm high.


I tried starting it up with the adjustment screws in a few different positions. first I tried with both screws in all the way on both sides but the idle raced up. Then I tried 2 and a half turns out on the air screws but it still raced. then the same thing but with the fuel screws out 1 turn then 1.5 then 2


The manual says to start with both air and fuel screws out 1 and 1/4 turns but that doesn't work at all either.


But I think I am getting somewhere with it
 
Back
Top Bottom