"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
glad t here :D i been out fer a short ride :D,short cause even in my gear i was freezin' :-[ :-\ frikkin krazy weather bro
yeah fuses are like sparkplugs easy to change out so's you can eliminate that possible fail
carry a small toolkit on these ole bikes with some o the stuff thats the way i do it
plugs fuses standard honda toolkit leatherman tape wire zips tieys a lighter etc

Where are you located??? Near me it was 81 out!! :D
 
Re: "Patina" The 1973 CB175 Cafe Racer

Found me a new ground spot and grinded the paint down. Is it possible to overload a ground? I have three terminals I need to ground and I was thinking about tying them to the same spot.
 
Re: "Patina" The 1973 CB175 Cafe Racer

9edeha5y.jpg
 
i dunno i dont think you can overload a frame metal just make sure everything is clean and if you are grounding to headlight bucket or to handlebars then run a ground strap from main frame, to, say your top yoke
the steer head bearings can sometimes be a poor path fer electrons
where am i ?
i am in southwest orygon,between merlin and grants pass
been wet most of a couple weeks now,but only just now got down there to that shoulda had the liner in the jacket cold
 
Re: "Patina" The 1973 CB175 Cafe Racer

Cool. I grounded everything under my seat. Used the light and everything tested out ok.

Tomorrow I'll grab a few fuses and see what I get.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Ok, new fuse, new grounds. Everything works right now. I'm going to take it for small 2 mile jaunts and park it and leave it each time for about 20 min. Then come back to it and see if it behaves. I'll update soon.

I used grease this time.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Round one went well. Went about 3 miles and returned home. Is it possible for a fuse to display symptoms of "going out" before it actually blows? Logic tells me that as long as the fuse is in tact, everything should function as normal, but nothing is logical about this anyway :)
 
Repeated heating and cooling from passing current in the presence of random high frequency vibration ? No , nothing I can think of that would produce difficult to find intermittent open circuits due to hairline cracks in the fuseable link and it's attachments .

news to me :o

~kop
 
Re: "Patina" The 1973 CB175 Cafe Racer

Thanks for the post, Kop.

Took her out for a second ride. In the past, the second ride after she cools always kills her...dunno why. This time around she ran like a dream. Carbs need some adjustment and I'm leaking like a rusty bucket out of my left crankcase cover but hopefully a fresh gasket and sealer solves that. It's a new gasket anyway so hopefully there's not a bigger issue.
 
annealed coper washers under the bolts/screws/fasteners below the nominal oil level . Hylomar or red aviation hi-tack in the spray or brush on can. I'm not so much a fan of gasgacinch except when I have to . Most metal to metal is Yamabond or Hylomar .

in a pinch I'll use "liberal" application of fingernail polish to 6mm threads with proper torque .

~kop
 
Re: "Patina" The 1973 CB175 Cafe Racer


kopcicle said:
annealed coper washers under the bolts/screws/fasteners below the nominal oil level . Hylomar or red aviation hi-tack in the spray or brush on can. I'm not so much a fan of gasgacinch except when I have to . Most metal to metal is Yamabond or Hylomar .

in a pinch I'll use "liberal" application of fingernail polish to 6mm threads with proper torque .

~kop

Interesting you say below the nominal oil level Kop. The leak is coming from the two bolts closest to the rear of the bike on the bottom of the cover. Kinda makes sense but it's nice to have you affirm that.

This surface does call for a gasket, but I know the cases were put together with Yamabond so that's good.

I'll look for some copper washers ASAP before I install the gasket. Right now I'm running stainless Allen head bolts with anti seize.

For the Hylomar, you apply to both sides of the gasket (cover and case)?

Thanks for the help, sir.

asyjuzyj.jpg
 
you either have a failed gasket or a badly scared surface that the gasket is supposed to seal on
it is also possible the screws are a bit too long bottoming out causing false security
a washer then would help
however none of those screws should require a copper sealing washer they have no acces to oil, if all is good with the gaskets and surfaces
sealing compounds have come a long way, get some loctite 518 it is all you will ever need for metal to metal flange and or gasket sealing/repair
it is worlds better than anything else available today
it also works extremely well as a thread sealant and removable thread locker
you should not need any sealer at all if surfaces are in good shape
on some of these side case gaskets however it is advantage to bond the gasket to one side so that future removal of the case is less likely to bust the gasket
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
you either have a failed gasket or a badly scared surface that the gasket is supposed to seal on
it is also possible the screws are a bit too long bottoming out causing false security
a washer then would help
however none of those screws should require a copper sealing washer they have no acces to oil, if all is good with the gaskets and surfaces
sealing compounds have come a long way, get some loctite 518 it is all you will ever need for metal to metal flange and or gasket sealing/repair
it is worlds better than anything else available today
it also works extremely well as a thread sealant and removable thread locker
you should not need any sealer at all if surfaces are in good shape
on some of these side case gaskets however it is advantage to bond the gasket to one side so that future removal of the case is less likely to bust the gasket

Thanks for that detailed response. I'll try a washer up under the lower bolts first to see if I am indeed bottoming out in the screw hole. Those darn stainless bolt sets don't come with any diagrams so you kinda have to eyeball where each bolt goes as far as length is concerned.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Another quick question before I take the cover off (assuming washers don't help)...

Does the clutch adjuster come off with the cover, or does it slide out when the cover comes off? I did this about a year ago and I want to say that the adjuster stays inside the cover when the cover comes off.

The manual doesn't have much detail around that part.
 
Re: "Patina" The 1973 CB175 Cafe Racer

So a jetting issue I think?

I can't get it to pull to the redline in any gear other than 1st. Even in first I feel like it was shuddering. At about 6k it just kinda fizzles out and loses power. Also strange idle issues. It will sit there and idle at about 1500-2000 and then all of a sudden the RPMs drop suddenly and it can't keep up.

Also I needed my choke today to get her started. Once she started she didn't like throttle blips much and either hesitated or back fired until she got warm.

Any certain direction I should go to chase this one?
 
Ignition timing. Get a strobe light on there. Aside from the uneven idle, it sounds exactly like the timing is retarded.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
Ignition timing. Get a strobe light on there. Aside from the uneven idle, it sounds exactly like the timing is retarded.

I have the Probe electronic ignition. Strobe light still applicable? My stupid question.
 
Always.

Strobe light is an excellent engine diagnosis tool.

If you're having engine problems of ANY kind, strobe light is the first step to ruling out any sort of spark issues.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
Always.

Strobe light is an excellent engine diagnosis tool.

If you're having engine problems of ANY kind, strobe light is the first step to ruling out any sort of spark issues.

Off to the auto parts store! They know me now :). I'll check back in soon after some YouTube videos and a trip to the store.
 
Back
Top Bottom