"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

If we can do it anybody can do it! Have fun!


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
If we can do it anybody can do it! Have fun!


Sent from my iPhone using Tapatalk

You guys are still my heroes :)


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

My heart goes out to a dear friend who I found out got in a terrible motorcycle accident recently. He was going about 45 through an intersection, laid eyes on the truck for a couple hundred yards with that "don't pull out in front of me" thought going through his head. Sure enough the guy pulled right out and hit him from the side. Ran right into him.

Compound fracture tibia and fibula and tons of nerve damage.

Do what's within your power to be safe out there guys.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Left side cover off. I hate cleaning gasket surfaces. There's gotta be a better way.

fcbd4b8951d428a18bd2b7df389429a2.jpg


CrazyPJ's starter block off plug from the inside.

1db9a9050ab6b7e5fcf64e60b13bf70f.jpg





Sent from my iPhone using Tapatalk
 
I see that my sprocket that is typically used for the starter chain is wobbling all over the place and spins freely unless mated with the rotor. I dont remember seeing that. Is that normal?

http://youtu.be/d7gRCQXKhfk
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
yes, it froats and when starter engages it spins the motor by meens of a sprag

Awesome. Thank you sir. I'll do
Something out of the norm and leave it alone :) haha
 
weeellll not a bad idea to inspect the sprag the screws can come loose you will need to pull the rotor to do dat
there are 3 rollers and tiny springs and bits as well
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
if you are keeping it kick only mite as well just delete the sprocket and the sprag parts ;)

That's what I was thinking. I think I'll need a rotor puller? Into the manual I go.
 
It does. That is the special secret Honda tool. Or get a friendly machinist to make you one.
 
Re: "Patina" The 1973 CB175 Cafe Racer

We use the rear axel and we use a steel sledge. A dead blow hammer won't work.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

The manual is worthless in describing this. I'm assuming you thread the axle in, tighten a bit and then tap tap tap until she pops loose? Assuming the cb650 is similar, saw a YouTube video where the guy just uses a refusal hammer and doesn't need much effort
 
Re: "Patina" The 1973 CB175 Cafe Racer


1sttimer said:
The manual is worthless in describing this. I'm assuming you thread the axle in, tighten a bit and then tap tap tap until she pops loose? Assuming the cb650 is similar, saw a YouTube video where the guy just uses a refusal hammer and doesn't need much effort
yep screw it in tight and wack it!


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Then leave the stator off and go total loss ignition for a bit just to feel what it is like to have a kilogram off of the rotational mass :)


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Then leave the stator off and go total loss ignition for a bit just to feel what it is like to have a kilogram off of the rotational mass :)


Sent from my iPhone using Tapatalk

Haha! No kidding! I'd like to feel what it's like to ride this thing without bugs first :)
 
Re: "Patina" The 1973 CB175 Cafe Racer

I think it is the shockwave that releases the stator and that is why a dead blow hammer doesn't work...


Sent from my iPhone using Tapatalk
 
Back
Top Bottom