Post a pic of your latest purchase

redwillissuperman said:
Can I have the one that you showed on the trailer? Need a. Either for this one...

ffb35301d95bb1f108fd96c5612a7b15.jpg
I just got that one moved into place. Replacing the cnc control on it in the next week or two with something new, probably MachMotion. And doing 4 axis control rather than two, that it is currently.
 
It ran on a phase converter in my dad's garage for 12 years. Probably going to ask $3,500 for it.
 
Get a VFD for $150 and you can pretty much run anything motor driven with household electricity.
 
Phase converter the old man bought for that one, still sells for $150. Run three phase machines on 110. Worked like a charm.
 
Tune-A-Fish said:
Seems cheap, comes with vice and all in the pic? starter tool kit?
No dice, on the vice, rotary table, or tooling. Will come with the DRO, and powerfeed.

I'm about to hook a servo up to that rotary table and run it as the 4th axis on the cnc Bridgeport I picked up.
 
So for me to tool it I can buy a combo hobby rig for dust collecting haha. Prechiatecha Brah But I just don't have the splash to play in your sand box :o
 
No worries. Figured I'd offer it up. I'll keep an eye out for the hobbyist rigs around here. They pop up quite often.
 
J-Rod10 said:
No worries. Figured I'd offer it up. I'll keep an eye out for the hobbyist rigs around here. They pop up quite often.
hey jrod where can i find a .593" diameter simple straight reamer for finishing/final sizing a bore in a housing for the du bushing light press fit ?
thanks in advance
 
xb33bsa said:
hey jrod where can i find a .593" diameter simple straight reamer for finishing/final sizing a bore in a housing for the du bushing light press fit ?
thanks in advance

http://www.valleytool.net/

That is who I buy custom made tooling from. Not cheap though.

I usually throw one that's a little over the size I want on the surface grinder and grind it to the size I need.

Probably be cheaper to find a shop that will do that for you, than to buy a custom made one.

Last tool I bought from Valley was a .110 drill .125 ream combo. Set me back $150.
 
Where are y'all getting these nice machines so cheap?

Somebody PLEASE keep me in mind for your next hand-me down lathe (medium size / bench-top)
 
On the "off topic" cr@p, y'all do know that there is a direct Private Message system on this forum, right?
 
J-Rod10 said:
http://www.valleytool.net/

That is who I buy custom made tooling from. Not cheap though.

I usually throw one that's a little over the size I want on the surface grinder and grind it to the size I need.

Probably be cheaper to find a shop that will do that for you, than to buy a custom made one.

Last tool I bought from Valley was a .110 drill .125 ream combo. Set me back $150.
thanks for the info
its a dead simple machining operation "pay someone to do it" fuck me it didnt take you long to learn about head fucking the other machinists did it did it hahahahahahahahaah one of my favorits is ask the machinist is that the same one ?
 
Got tired of waiting on an unresponsive seller in the classifieds section ::)
Picked up this instead...
FullSizeRender_zpsjzu3gexa.jpg
 
xb33bsa said:
hey jrod where can i find a .593" diameter simple straight reamer for finishing/final sizing a bore in a housing for the du bushing light press fit ?
thanks in advance

Xb, here ya go
http://www.mscdirect.com/browse/tn/Holemaking/Reamers/Chucking-Reamers-Sets/Chucking-Reamers?navid=12106128#navid=12106128+4288061800
 
Redbird said:
Got tired of waiting on an unresponsive seller in the classifieds section ::)
Picked up this instead...
FullSizeRender_zpsjzu3gexa.jpg

Nice! I've tossed around getting one for years too
 
Back
Top Bottom