Roc City Cafe Racers

I have the daytona seat (I think) and its a GREAT quality seat. Customer service is good also. You won't be disapointed.
 
My seat, front fender, and tank came from Sean. I also purchased a set of his clip-ons, though didn't use them (no problem with the clip-ons, I just went with something else). All par ts are of excellent quality and I wouldn't hesitate to buy from him again.
 
RCC is a great company to deal with, and were even mentioned as a hot spot for Cafe parts in the latest motorcycle classics if i'm not mistaken.
 
Probably some of the best cafe parts produced in the U.S. Along with that U.S stamp though comes some over priced fiberglass pieces. I don't mean that poorly at all because he is more than fair on a lot of other parts. Metal work is some of the best you'll ever see. I would suggest for sure going through there website as I got no response through their ebay page TWICE before I found this forum.
 
CBdublin said:
Probably some of the best cafe parts produced in the U.S. Along with that U.S stamp though comes some over priced fiberglass pieces. I don't mean that poorly at all because he is more than fair on a lot of other parts. Metal work is some of the best you'll ever see. I would suggest for sure going through there website as I got no response through their ebay page TWICE before I found this forum.

I have to disagree with the overpriced fiberglass. Shop around, RCC's glass parts are very competitively priced compared to other parts of similar quality. Sure, you might be able to find something a bit cheaper on Ebay, but who knows where it came from or what the quality will be?
 
Thanks guys. The main reason I asked was because I thought the prices for the glass parts were a bit too good. Looking at his other work I can see that he really digs what he's doing and takes pride in his work. I'll be ordering from him shortly.
 
TerryK said:
Thanks guys. The main reason I asked was because I thought the prices for the glass parts were a bit too good. Looking at his other work I can see that he really digs what he's doing and takes pride in his work. I'll be ordering from him shortly.

Just remember that Sean's running a small shop and is pretty busy. You'll get your parts and they'll be of excellent quality but he can be a bit slow to answer emails at times and you may not get automated shipping notices with tracking numbers as you might with a bigger outfit.
 
Wingspan said:
Just remember that Sean's running a small shop and is pretty busy. You'll get your parts and they'll be of excellent quality but he can be a bit slow to answer emails at times and you may not get automated shipping notices with tracking numbers as you might with a bigger outfit.

That wont be a problem. I'm in no rush.
 
Good to hear you're choosing quality, and Wignspan, I humbly retract my previous statement regarding RCC's fiberglass prices. I may just be getting old but I swear he had some plan seats over the $2 range before. Upon checking the current inventory and prices I have to agree some amazing quality for a fair cost. I think I'd trade a testicle for that GP tank he makes.
 
CBdublin said:
Good to hear you're choosing quality, and Wignspan, I humbly retract my previous statement regarding RCC's fiberglass prices. I may just be getting old but I swear he had some plan seats over the $2 range before. Upon checking the current inventory and prices I have to agree some amazing quality for a fair cost. I think I'd trade a testicle for that GP tank he makes.

The seats don't cross over the two bill mark unless you go for the upholstery as well. The tanks are pretty cool. The CR tank Sean did for me really made my bike.
 
Be sure to give everything a good look. While I don't have any complaints, the clip-ons that I bought had a very small fragment of metal sticking up on the inside of them (on a weld), that could have potentially cut into the wiring that runs through the bars on Hondas. A few seconds with a file took care of the issue, so I never brought it up to Sean, but worthy of note.
 
Got my "Interceptor" seat the other day and I have to say it is of great quality and well finished. I'm very happy with it and at $101 it's a bargain.
 
I'd also like to give a big thumbs up for Sean at Roc City.
He made a custom aluminum tank for my '73 350F, it looks amazing, and everything about the process from ordering it to sizing it to the thrill of receiving it was great. Sean is super and his stuff is first rate. And I think the prices are extremely fair.
 
I would like to give Sean and the RCC crew a props.

The customer service was great. Answered every question i had (which was many), and worked with me when I made dumb newbie mistakes. Both seats I received from RCC were thish solid and well made.

Although my customizing skilld of the finished seat probably don't do it justice I am thrulled with the whole experiance. The mounting on an odd framed bike (GS450) was a task, and the tank matching (of my own doing) created issues. The seat and its quality (and ability to not flex under 220 LBS made the whole situation much easier than it could have been with another brand seat or an ABS look alike.

American made, Proud of what he does, and for good reason! I am sold on the RCC styles and quality.
 
Back
Top Bottom