SUPER CAP BANK - will it work?

crazypj

Split personality, I fake being smart
Been thinking about this or about 18months, finally decided to make something.
Also posted in my 'CB 360-Build to Blog'
Copper-clad board to make a PCB, Sharpie to draw out the bits you need to keep and Muriatic acid plus Peroxide as an etchant (1 acid, 2 peroxide)
Took a while to sort out what I wanted then just drew on board. Sharpie 'ink' is some kind of plastic/polymer?
20 mins later, got this
First%20ever%20etched%20board.jpg


Going to have 4 rows, 3 to a row of 5.5v 1.0 Farad 'mini' capacitors
3x5.5=16.5volts per row so within the range of 360 charging system 8)
No idea how well it will work (or even if it will work?)
MLK may be along later to tell me what I'm doing wrong? ;D
Pretty rough and ready but I think OK or a irst ever attempt at making a circuit board (it isn't a PCB as no printing is involved ;) )
It's going to be about 4"x3"x3/4" and several pounds lighter than the 7A/hr battery I was using
 
Might be a little low on capacitance. I'm counting about 12,000µF?

The ones I use for the SR and XS (with PMA) are usually in the 30K range. I usually use for the 40V version, too.

I'm certainly interested to find out, though.
 
Caps say NEC 5.5v 1.0 FARAD
I was thinking I would get 4 F with 4 rows at 16.5v?
 
Unfortunately, the voltage on caps doesn't stack. It's more of a max rating than a discharge amount. Rule of thumb is to use about twice the rating as you'll need. So 14V or so should be a 25V cap.
 
Hmm, not what I've read everywhere else?
3 in series should give 16.5 V but only 1/3 capacitance plus some losses from solder, tracks, etc.
I made mistake when I said 16.5 V @4 F :-[
4 banks in parallel should give 1.3 Farads at 16.5V in a very small package. 80% is usually max rating for charging
Even if I only get 1F it will be way higher than the 36,000~ 80,000mF normally used
I have a couple of Mallory 30v 18,000mF, may add them in parallel to get another 36,000mF, should smooth out the transer to cap bank
I may add a few more parts and pieces for charge balancing or maybe just try it and see what blows up ;D
If it actually works as expected I'll get new caps instead of used ones and maybe add some extra for higher volt ceiling.
I would like to get a set of the 2.7V Ultra Caps but they are physically quite large so take up a lot more space than a stock battery
(plus real expensive)
http://www.ebay.com/itm/6X-3000F-2-7V-Maxwell-ultracapacitor-super-farad-capacitor-booster-cap-BCAP3000-/181391254764?pt=LH_DefaultDomain_0&hash=item2a3bc2e4ec
Oh, the larger holes in etched section are going to be for mounting plate, the smaller ones at ends of tracks are for caps. the 4 rows will be vertical in pic. + - + - + - +- for top and bottom rows, - + - + - + - + in middle row
Rectifier diodes should block reverse low back to generator winding just like a stock battery gets blocked. I'm expecting leakage so caps will drain relatively quick but charge up just as quick (fingers crossed ;) )
Just seen these, could be real interesting to get some
http://www.ebay.com/itm/10-X-5-5V-4F-Farad-Ultracapacitor-Super-capacitor-v-Type-Power-backup-/181469378595?tfrom=181391254764&tpos=top&ttype=price&talgo=undefined

Amp ratig is real low, seems the smaller the physical size the less amps you can put in (or take out) Maybe I'll stick with 1.0F same dia, 3 times taller ;D
 
Well, it kinda works on bench (adjustable) power supply and voltage is 'shared out' reasonably well.
Each row of 3 reads same as input voltage (after I removed a bad cap and fitted spare)
Weight without connectors is about 5 ounces
I'm still testing individual voltages, no idea how old these capacitors are plus they are used and could have had excess voltage applied at some time (makes them fail)
It means bike should in effect be running direct off generator with the capacitors acting as a 'store' between the 'power pulses' plus a little reserve to keep them charged
All appear to be working, some better than others though
I've ordered some new ones which should work much better plus some 5.6v zener diodes so each cap will be bypassed to the next if anything goes wrong and then to whatever load is on circuit (coils, lights, etc)
 
Back
Top Bottom