"Woods" - '73 CB350F

Re: "Woods" - '73 CB350F (New Parts)

My hand made clip-on brackets arrived today, courtesy of Swagger. They look badass and I can't wait to get these on and ditch the clubmans. I'm sure once I get those on it will run properly too ;)


Anyways, hopefully I can get all this sorted soon as this weekend is my last bit of freetime for the next month or so. Chicago next week and then I'll get out of the country till the end of May.


Again, props to Swagger for some really nice craftsmanship.
Seattle-20110421-00028.jpg
 
Re: "Woods" - '73 CB350F (Getting there!)

Today I pulled off the front end. My top triple had cracks on both sides so I bought a new one a while ago and fitted it today. As I loosened the bolts on the sides, the triple came off in 3 pieces... scary to think I was riding it with that. Anyways, took off the forks and ditched the tin covers for some gators. Also installed new headlight ears and the clip-on brackets from Swagger. I cut some drag bars down and they look great on it. Still have to run electronics through the bars. I'm probably going to ditch my speedo and make up a new bracket for the tach. Also need to refill my front brake as I bled it. I'll add some photos if I make it down to work on this tomorrow.
 
Re: "Woods" - '73 CB350F (Update + Photo!)

Today I got all the main stuff up front taken care of. Finished stripping the paint off the top triple, ran wiring through the bars, removed excess wiring from old stuff, fixed my throttle (it used to stick) rerouted some cables, pulled off the speedo and made up a temp tach mount out of aluminum. All that's left up front is to fine tune that tack bracket and make it up using steel. I'm super stoked with how its coming together. Started the bike up and let it run for a bit. Carb one always starts pissing gas about 3 mins into running and then the bike runs crappy and dies. I'm pretty sold on either float height or needle. Maybe I accidentally put the needle in upside down? I'll get back to that next weekend as I'll be out of town this next week.


Photo from today:
TripleandClipons.jpg
 
Re: "Woods" - '73 CB350F (Brake light only from rear lever?)

Here is a quick one for you guys: Any idea why my brake light only lights from my rear brake lever and not the front? Its an LED light with two lines off positive side (one with resistors to achieve the running light) and a ground.
 
are you running stock levers? if they're anything like the 360's then there's a little pin that completes a circuit when the lever is at rest. probably something happened to the wire that attaches to that pin when you swapped handlebars?
 
If I recall correctly there was an orange/yellow wire that may have went to the lever. Thanks for the heads up on the pin, I'll pull out the manual and see what I find
 
So they work fine off the rear brake pedal but not by pulling front brake lever, correct?
Ok....so first thing I'd check is your front brake switch. You can do it really easily with a multi-meter, all you need to do is verify that it's changing state with actuation. If it's normally open you want it to close the circuit and obviously the other way around if it's normally closed. Once you know that your switch is working, make your way down stream in the harness, along the wires that connect the switch to the brake light. You'll need a wire diagram too.

Somewhere the 'signal' that the brake light needs (+12v or chassis ground) isn't getting there. If you can eliminate the variables you'll find the problem.
 
Re: "Woods" - '73 CB350F (Still alive)

I figured I had better post something, as it has been nearly a month! I haven't seen the ol bike since the end of April, as I left town on May 4th. I'm currently in the Middle East for work (not military related, no worries) and will finally be headed home this coming Friday.

Yesterday I got bored and ordered something REALLY COOL for the motorcycle, so I hope it arrives by the time I get home. You guys are going to have to wait till then... I wouldn't want to spoil the surprise (unless you have seen me post on a different thread about it :X).

Anyways, still alive and well. Can't wait to get home to do a bit of wrenching and ride.


Cheers
 
m in sc said:
your problem is either electrical or fuel flow to the carbs. jetting wont do that.

check petcock/gas tank vent for blockages
Jumping back in time to when the bike stranded me and I had no idea why... I ended up figuring it out and forgot to update about that. Turns out it was electrical. Back when I had wired in the brake light I just twisted together the conductors and taped them up, as I did not have the soldering iron with me. Well, ended up forgetting to revisit that. When I got the bike back to the shop I was recalling how the headlight looked dim when it was stalled in the parking lot, but just ruled it out as i figured it was the sun making it look dim. Well I turned on the ignition and kicked the piss out of it back at the shop. Headlight was glowing bright. Turned off the key and rested for a few. Turned it back on and the headlight was bearly glowing! I knew it! Pulled the seat and one of the leads had come lose and was touching the frame.

After getting over how stupid I felt, I drove to the store, bought some solder and promply did a proper job.

Good call on th electrical issue!
 
Re: "Woods" - '73 CB350F (Charging problem)

Haven't been around in a bit, super busy with work things. Anyways, troubleshot my charging issue and I think it's a bad Rectifier. Charged up the battery and measured about 11.8VDC at idle across the battery terminals. Brought the bike up to 4-5k and that reading did not increase, so the battery obviously isn't charging.


I guess should buy this?:
http://www.electrosport.com/honda-cb350f-750f-regulatorrectifier.html
 
Re: "Woods" - '73 CB350F (I'm still alive!)

Ordered a new rectifier/regulator combo today that should arrive before the weekend, so hoping to get this thing going again. Also repaired the connections on the magnetic switch for the elec start (not that i will use it now) as one of the bullet connectors was toast. So i'll update this weekend with long overdue photos to include the new exhaust and front end!
 
Back
Top Bottom