XS850 - Monoshock & USD Fork (pics pg 13)

Re: XS850 - Monoshock & USD Fork

Alright, so now that I have brakes, I finally got out on the road for a test drive further than just down the street. It was running a little choppy, so I figured I'd start by checking the plugs to see what was going on. Results...

Left plug: Charred black
Center plug: white
Right plug: white

Leaning towards resyncing the carbs first, then jumping into jetting. I'm running the MKII's with what I believe to be stock jetting (should have taken note of the sizes when I had them apart. Dammit!). UNI foam filters. Fairly open 3-3 exhaust. So I would expect it run a little lean, but it's the charred black plug that has me confused. Air screws are in the factory position.

I did a carb sync with my vacuum tool right after I put it all back together, and I thought I had it pretty close. But the inconsistency in the plug results make me think I should probably try again.
 
Re: XS850 - Monoshock & USD Fork

Charred one possibilities: NOT firing, weak spark, float level is too "low" so the level in the bowl is too HIGH. Or fuel isn't shutting off at all? Could also be mixture screw settings.

They should all be white and you should have trouble running the bike with stock jetting and the Foam filters/exhaust. Swap out the one plug first so you can rule out faulty plug, verify that the spark plug boot is properly attached to the wire and has spark (not loose) And verify mixture settings. Those can all be done without pulling the carbs first. If that plug goes black again after you verified good spark on a new spark plug. I'ts one of the above mentioned things, more likely a stuck float/too much fuel in the bowls.
 
Re: XS850 - Monoshock & USD Fork

datadavid said:
But the idle was so strong...?

Yeah it idles pretty well. And at mid-full throttle, it screams. It's just off idle/low throttle where it has issues. So air screw/pilot system most likely.

Unless of course it's a spark issue. I'll check spark again. The plugs are all brand new, so it shouldn't be a bad plug. Wires are all stock/original... so I should probably replace those anyway.

It's definitely sooty, not oil fouled. So I'm not worried bout ring at this point.
 
Re: XS850 - Monoshock & USD Fork

What are your mixture screws at then? 2 of the 3 cylinders will run that bike (I owned a 750 that was a pile. Great highway ride when she was running properly) So it sounds like the stumble is due to that cylinder being off, once higher in the revs it's "hidden" and most likely burning the fuel given, so I think you are right with the pilot system/mixture is very likely :)
 
Re: XS850 - Monoshock & USD Fork

MotorbikeBruno said:
What are your mixture screws at then? 2 of the 3 cylinders will run that bike (I owned a 750 that was a pile. Great highway ride when she was running properly) So it sounds like the stumble is due to that cylinder being off, once higher in the revs it's "hidden" and most likely burning the fuel given, so I think you are right with the pilot system/mixture is very likely :)

I set the air mixture screws based on the manual... I don't remember the exact number of turns. I can check to make sure they are all the same, but I think they are. Assuming they are, I guess I can pull the float bowl to make sure the float isn't sticking, but I'm pretty sure it isn't because I'm not dumping gas everywhere, which is pretty standard on these bikes with a sticky float.
 
Re: XS850 - Monoshock & USD Fork

Saw this on another forum:

"Butterfly Shaft Seals are one of the first places to start looking for a high idle, or a lean idle mixture.

That is because while many people mess around with carbs, very few pay attention to those seals. They are not listed as separate items in the parts list, and for some reason, disturbing the butterfly valves scares the crap out of most people.

That is good, because if you get it wrong you will destroy the carbs.

So, for most of us, those flimsy rubber seals are 30 years old, and hard as iron. They are due a change, and it's really very easy and nothing to be scared of.

The two screws holding them to the shaft are threadlocked. So .... GEt a good fitting screwdriver, hold a little torque on the screw and gently tap the end until you jerk it free. Go easy, and they come out easy. If you did it right you can re-use the screws. If you did it wrong then replace them with socket head screws and make the next guys job easier.

If you did it really, really wrong you bent the shaft and you will be paying eBay a visit ... It shouldn't come to that

Use threadlock (blue) on assembly. Tighten then gently, open and shut the valve a few times to center them, then lock them down.

The rest of the job is simply assembly."


But honestly, we KNOW you are running lean due to the change in your intake and exhaust and not necessarily these butterfly seals they speak of :) So I would try 1 full turn more rich than the stock mixture screw setting to get you started. You may end up needing to go UP one size on the pilot jet to get it sorted fully. And either way, you've got something off on that sooty cylinder. Start with the float height and let us know what you find. Can't wait for you to get her running up to snuff.
 
Re: XS850 - Monoshock & USD Fork

Thanks for the input. I think you're right though... step 1 is to get that sooty plug to look like the rest. Then I can try to dial them all in at the same time. Getting cards 2 and 3 richer could be as easy as a 1/4 to 1/2 turn on the air mixture... but I don't want to do that until I figure out the cause of the black plug in #1.
 
Re: XS850 - Monoshock & USD Fork

treitz said:
Thanks for the input. I think you're right though... step 1 is to get that sooty plug to look like the rest. Then I can try to dial them all in at the same time. Getting cards 2 and 3 richer could be as easy as a 1/4 to 1/2 turn on the air mixture... but I don't want to do that until I figure out the cause of the black plug in #1.

Yep! It's too tempting to "fix" other things. And then you have no idea what actually was the cause and if you masked it, or fixed it properly. :) Good luck sir!
 
Re: XS850 - Monoshock & USD Fork

I ended up with 137,5 mains in my yellow 750, which had pod and 2" 3-1 exhaust iirc.. so you will probably be dangerously lean with that setup in the end. Running 3-3 will probably require smaller mains though.
 
Re: XS850 - Monoshock & USD Fork

datadavid said:
I ended up with 137,5 mains in my yellow 750, which had pod and 2" 3-1 exhaust iirc.. so you will probably be dangerously lean with that setup in the end. Running 3-3 will probably require smaller mains though.

While I'm checking the float height, I should probably pull the jets and takes notes this time huh? haha

Would be good to have an idea of where I'm at so that I know where I need to go.
 
Re: XS850 - Monoshock & USD Fork

treitz said:
While I'm checking the float height, I should probably pull the jets and takes notes this time huh? haha

Would be good to have an idea of where I'm at so that I know where I need to go.

Indeed. I think a slightly lower main than david, and maybe a half step on the needle height and you might be set! :) that is...after you find your float issue...ha! (sorry I HAD to!!!)
 
Re: XS850 - Monoshock & USD Fork

MotorbikeBruno said:
"Butterfly Shaft Seals are one of the first places to start looking for a high idle, or a lean idle mixture.


Just had to add some emphasis to how true and important this is. Lots of old carbs don't even have seals, and relied on having a close fit between the carb body and shaft which is of course absurd, even when new, but crazy once worn. I have taken quite a few carbs like that and machined them to accept seals from carbs that did have them and I can't think of ever doing more totally satisfying work. Absolutely FIXED - no doubt whatever - makes a carb that you want to throw against a brick wall into one that purrs like a modern digital injector system.
 
jpmobius said:
Just had to add some emphasis to how true and important this is. Lots of old carbs don't even have seals, and relied on having a close fit between the carb body and shaft which is of course absurd, even when new, but crazy once worn. I have taken quite a few carbs like that and machined them to accept seals from carbs that did have them and I can't think of ever doing more totally satisfying work. Absolutely FIXED - no doubt whatever - makes a carb that you want to throw against a brick wall into one that purrs like a modern digital injector system.

This is great information and good to know for future builds. Thanks for sharing!

MotorbikeBruno said:
...after you find your float issue...ha! (sorry I HAD to!!!)

Haha yeah yeah. I'll find the issue first.
 
MotorbikeBruno said:
Indeed. I think a slightly lower main than david, and maybe a half step on the needle height and you might be set! :) that is...after you find your float issue...ha! (sorry I HAD to!!!)
Yea jetting after fixing other issues of course!
I've been thinking about putting a one step bigger main in the middle carb, but can't really decide if its hotter running temp will make it run worse, or if the bigger jet will make it run cooler...?
My 750 overheated and simply stopped running the first longer run i did with pod+exhaust changes.
Embarrassing as i was riding with one of swedens most renowned bike builders! :D
 
Technically more fuel = colder operation, which is why running lean creates so much excessive heat. But due to the fact that the center 2 get more hot than the outer 2 cylinders, you need less fuel to do the same thing the outer 2 are getting. So generally speaking 1/4 have LARGER jets to compensate for the cooler running cylinders. If your engine is water cooled, this is more of a moot point, but some of the manufacturers still did the 2 different jet thing. I feel like it was an R6 I worked on that might have had the dual jet sizes in it. Can't remember.

As for overheating. Change your spark plug to one degree colder. Those run D8EA or so right? For NGK the HIGHER the number, the COLDER it is. So try D9EA instead or DR9EA if it needs the resistor plugs. Or better yet, fit an oil cooler if you don't already have one.
 
Mine had ngk heat range 7 iirc, never overheated after rejetting except when marching at 140kph in 30'c, which they seriously need oilcoolers for!
Found a nice lockhart cooler for the one im building now since its bored out(896cc) and running higher comp.
Using a set of triumph legend mikunis with 140 mains.
Not sure if its right since it wont shift through the gears under load...
 
MotorbikeBruno said:
As for overheating. Change your spark plug to one degree colder. Those run D8EA or so right? For NGK the HIGHER the number, the COLDER it is. So try D9EA instead or DR9EA if it needs the resistor plugs. Or better yet, fit an oil cooler if you don't already have one.
Perhaps a bit of re think here. Spark plugs in the main have virtually no impact on engine temps (excluding race engine running scary lean and one heat range hotter pushes it over the edge, etc). Plug heat range selection should be based on how hot the plug runs based on how the engine performs. Spark plugs run hotter or cooler based on their ability to transfer heat into the head, but they have little to do with how hot the engine itself runs. If the insulator is too hot (blistering - glassy etc) a cooler heat range should be selected, but it needs to run hot enough to keep the insulator clean. Plugs that run too hot need shorter insulators with more contact area to the housing for a better path to transfer heat into the head, and just the opposite if they are too cool - longer more exposed insulator and less contact area to transfer less heat. Looking at and comparing say a 7 series NGK to a much colder 10 you will see this obvious physical difference, but the spark both make and the way the fuel burns is identical. Run the 7 and check the cylinder temp and then a 10 you will not see any temp difference aside from either frying the 7 or fouling the 10. As long as they are working well they will run very much the same. If you are suffering from an overheating issue and not lean (and nothing else is suspect) look for less ignition advance as a possible cure. I'm in Florida, and with the humidity, temperature, high alcohol gas, and dreadful traffic, high temps are more than annoying on an air cooled bike! That oil cooler advice is good!

The stock plugs are very likely the ones you will end up with, so just keep those until you have everything else sorted out.

I would leave all the factory jetting until I got the black plug problem sorted. Good idea to take the carbs completely apart and verify all the adjustable parts - jets, slides, needles etc to make sure some oddball part didn't find its way in there some how. Very likely that will be an obvious problem once you find it. Carefully set the fuel levels, and if you have any doubts, check them on the bench. You can fill them with fuel and just check the volume manually either by very carefully pulling the bowls and visually looking at how full they are and comparing, or if they have drains comparing the volume that drains out. It is pretty hard to be super accurate, but should show some issue if present.

Once the black plug gets sorted, ignore everything else until you get the main jets where you want them. Wide open throttle, max horsepower (= max air drag, so as fast as she goes) plug chops. You HAVE to physically cut the plug apart to read it!!!!! Once you get that done you can tinker with everything else to get it to drive best - otherwise you will be chasing your tail for ever!
 
Nicely stated. I've worked on so many machines that "just had the wrong plug" in them and they were always one degree hotter than stock. This caused a few of them to overheat easily. Not to cause too much of a threadjack with debate, but doesn't the excess heat from engine combustion go into the spark plug itself, and thus creates higher cylinder head temperatures? I suppose I'll have to do some more research as I may have just been unlucky and found bikes that overheat with the hotter plugs in them :) One seized while idling (jerk had 2 heat ranges hotter in there...) put correct plug in and she runs fine. Interesting isn't it? Good call on the ignition timing being a likely culprit JP.

From NGK website:
Causes of Overheating:

Spark plug heat range too hot
Insufficient tightening torque and/or no gasket
Over-advanced ignition timing
Fuel octane rating too low (knock is present)
Excessively lean air-fuel mixture
Excessive combustion chamber deposits
Continuous driving under excessively heavy load
Insufficient engine cooling or lubrication

Back to the thread. Hopefully Treitz can solve his black plug issue soon :)
 
Sure, overheated sparkplugs will cause detonation, since they will virtually be glowing hot in the engine. Right plugs for right operating parameters i guess.
 
Back
Top Bottom