XS850 - Monoshock & USD Fork (pics pg 13)

jpmobius said:
...Once the black plug gets sorted, ignore everything else until you get the main jets where you want them. Wide open throttle, max horsepower (= max air drag, so as fast as she goes) plug chops. You HAVE to physically cut the plug apart to read it!!!!! Once you get that done you can tinker with everything else to get it to drive best - otherwise you will be chasing your tail for ever!

What do you mean by physically cut the plug apart to read it? This is news to me.
 
Beware the Novice Mobius ;)

Even the best shops don't do chops by the book, so i would suggest just reading the smoke ring in the plug you can see without any destructive testing, use a good light and readers whatever, and I would worry about the liability in asking you too "go as fast as it goes" but a good mile chunk of road and a solid WFO chop will suffice LOL
 
Tune-A-Fish said:
Beware the Novice Mobius ;)
And don't you forget it!

MotorbikeBruno said:
but doesn't the excess heat from engine combustion go into the spark plug itself, and thus creates higher cylinder head temperatures?
Well . . yes er, sort of. The thing to realize is that the plug itself does not add (or remove) any energy to the system. All are nearly the same mass and material. All add (microscopically) the same energy into the system. A hot plug may run hotter in actual temperature - potentially greatly - but it is only hotter because it can not conduct the heat it absorbs from combustion away into the cylinder head fast enough. Usually this is worse for the plug itself than substantially impacting overall temperature, but no doubt if run hard enough, long enough, or lean enough etc etc, the combination of many factors including the plugs higher average temperature can result in higher engine temps. Certainly if it becomes a glow plug it will in fact become the cause of catastrophic overheating! That said, I will stand on my original comments, as I think they are very pertinent for Treitz solving his issues. Good discussion for another time and place agreed!

No doubt our young whippersnapper Mr. Tuna can see the bottom of the insulator but it's been a terrible long count of days since my eyes worked that well. It is in fact doable - but we novices like to get a better look! I suggest for people to cut their plugs for that reason, plus the fact that you can't really get a good second reading anyway, so if you are still tuning you need new plugs anyway. Plugs are cheap, though not so much if you run through very many. Lots can be gleaned from reading spark plugs, but most people think looking at the "color" is what they need to do. Getting that perfect tan coloring is not a bad thing, but it is mostly unimportant in determining good fuel ratio. What you are looking for is at the very bottom of the insulator and is quite difficult to see even if you know what you are looking at.
Found this:http://www.strappe.com/plugs.html. Good stuff - and there is good ignition timing info there too. I cut my plugs all the way around under the hex section so the entire bottom portion of the steel housing falls off - very easy to do and gives comprehensive exposure of the insulator without damage. Sorry I couldn't find better pictures but you should get the idea. Doing this gives an exceptionally good view and confidence inspiring ability to interpret what is happening with your wide open jetting.

And for the record, I would like to retract any misleading advice I may have unintentionally and inadvertently given to recklessly operate a motor vehicle at top speed. WFO for a mile is a much more prudent course of action endorsed by the more responsible (and respectable) members of our society.
 
jpmobius said:
And don't you forget it!

HAHA... Love it!

WFO for a mile is a much more prudent course of action endorsed by the more responsible (and respectable) members of our society.

Let me post a retraction also here ::) I meant have a mile to wich you can operate a scooter at WFO safely for as long as you are mentally capable :o Aaaand... I work hard to maintain that status among my peers here at DTT... :o :o
 
Okay... so I looked at the bike a little last night.

1) I checked electrical, and I've got big fat spark on that left cylinder. So that's not the issue.

2) Checked float height and the left matches the right. I used the hose technique out of the float drain, so I'm not sure if the heights are RIGHT, but they do match. I of course set the float height to the specs in the Clymer manual prior to putting the carbs back on the bike.

Once I get my new clutch cable on I'll run it a little more and if I'm still having the same issue. If yes, then I guess I better take the carbs apart and check my jets & needle.
 
Nicely done. Did you try a new spark plug just for good measure (to see if maybe it was fouling before and not now?) Also, what are the mixture screws set at again? Is there an O-ring and washer for each mixture screw? Just checking :)

Can't wait to see what the issue may have been!

Bruno
 
I imagine if it was an air mixture screw malfunction the screw would be loosening, not tightening, causing a lean mixture, not a rich mixture. ??

I was sort of hoping it WAS the float because that's easy to adjust. Now I'm back at square 1 really.

The air mixture screws are all set at the stock level. I'm sure I need to go in a bit to richen the mixture up, I'm just waiting to do that until I figure out the one sooty rich plug. At this point I would have to go in on the right 2 cylinders, and out on the left one which seams more like a bandaid than a fix.
 
But.. on those carbs, i am pretty certain the mixture screws control fuel, not air. Air is controlled by the butterflies.
That is at least the assumption i've made since turning them in leans the idle out. Used my nose.
Also iirc the service manual mentions this, also the yamtriples forum.
 
datadavid said:
But.. on those carbs, i am pretty certain the mixture screws control fuel, not air. Air is controlled by the butterflies.
That is at least the assumption i've made since turning them in leans the idle out. Used my nose.
Also iirc the service manual mentions this, also the yamtriples forum.

Hmm, I'll have to check the manual. I am running the Mikuni MKII carbs (just to be clear). I was under the impression that turning the air screws out would lean the system... but I guess I made that assumption based on my experience with other carbs. If these are backwards, that sure is good to know now!
 
My bad, picked through a few old posts on yamtriples forum, and they actually seem to control air mixture, not gas.
Still wont explain why my mic mk2's ran leaner when screwing them in..
 
Being that it is the idle circuit, may be possible you had too fat of a pilot so turns in would lean it out after the flood??
 
No no gents! Rule of thumb FRONT mounted mixture screws are AIR mixture screws. IN = rich. REAR mounted mixture screws adjust FUEL (like these on the MK2's) OUT = rich.

Think of it this way. Air comes into the front of the carb so you are metering how much AIR gets into the pilot circuit. Anything past the middle of the carb is fuel related, so a REAR mixture screw will adjust the amount of EXTRA fuel going into the throat to make your bike happy.

Also, found this linky below.

http://www.yamahatriples.com/index.php/how_tos/carb-rebuild-mikuni-mark-2/
 
MotorbikeBruno said:
No no gents! Rule of thumb FRONT mounted mixture screws are AIR mixture screws. IN = rich. REAR mounted mixture screws adjust FUEL (like these on the MK2's) OUT = rich.

Think of it this way. Air comes into the front of the carb so you are metering how much AIR gets into the pilot circuit. Anything past the middle of the carb is fuel related, so a REAR mixture screw will adjust the amount of EXTRA fuel going into the throat to make your bike happy.

Also, found this linky below.

http://www.yamahatriples.com/index.php/how_tos/carb-rebuild-mikuni-mark-2/

I'm very familiar with that thread as this is the second set of these carbs I have rebuilt. However on the first set I kept everything fairly stock, so I didn't have to mess with the air screws at all.

Your logic makes sense... I am very glad you brought this up. I had no idea!

Although I wonder why you're referring to the front of the carb as rear facing, wouldn't the front of the carb be engine facing (which is where the air screws are on this carb)? Maybe it's just a weird carb talk thing. I guess you could argue that the air enters from the front of the carb, just weird terminology.
 
MotorbikeBruno said:
No no gents! Rule of thumb FRONT mounted mixture screws are AIR mixture screws. IN = rich. REAR mounted mixture screws adjust FUEL (like these on the MK2's) OUT = rich.

Think of it this way. Air comes into the front of the carb so you are metering how much AIR gets into the pilot circuit. Anything past the middle of the carb is fuel related, so a REAR mixture screw will adjust the amount of EXTRA fuel going into the throat to make your bike happy.

Also, found this linky below.

http://www.yamahatriples.com/index.php/how_tos/carb-rebuild-mikuni-mark-2/
Well, that explains it then :D
 
Say - that is a great link! I would add a couple of comments. First, regarding removing the throttle shafts: I do not have a set of these particular carbs in front of me, so this is a generalization. Don't underestimate the difficulty in removing the little screws that secure the throttle plates to the shaft. Actually, they are not so much difficult as delicate. Many shafts are not steel but chrome plated brass, and as they have a slot carved through them for the throttle plate, they are quite easy to damage, and they will not tolerate even the slightest bit of damage. The little screws are steel, but very often they have been swagged on the end to mechanically prevent them from backing out. This means that they will be an interference fit backing them all the way out. This is actually really bad for the threads in the shaft, but I have never had one injured enough to notice by taking out the screws. You will need an EXACTLY CORRECT screwdriver in new condition. The trick is to support the throttle shaft directly behind the screw you are removing. I clamp a wooden support vertically in a vice that will scope through the venturi and back up the shaft directly. A hammer handle works great if you have one small enough to pass loosely through the bore. Once backed up, you can push down really hard on the driver to keep from stripping the head of the screw. Once you have the throttle plate out, it is a good idea to scrape a tool (I use the end corner of a small flat file) over the slot in case there is a burr before you slide out the shaft. Reassembly is easy - drop of blue loctite on the threads and assemble loose. Close the throttle plate all the way to align it perfectly in the bore and tighten the screws using the same wood back up as before. Remember, if your screws were swagged, they can be very tricky to start the threads as they can seem to be cross threaded when they are not.

The other thing is I never replace any of the brass - I clean and reuse the factory parts. I only replace needle/seat assemblies when they either have viton tips or are obviously worn or are known to leak. If I replace metering needles, I get factory OEM parts. I never use any brass from rebuild kits.
 
treitz said:
I'm very familiar with that thread as this is the second set of these carbs I have rebuilt. However on the first set I kept everything fairly stock, so I didn't have to mess with the air screws at all.

Your logic makes sense... I am very glad you brought this up. I had no idea!

Although I wonder why you're referring to the front of the carb as rear facing, wouldn't the front of the carb be engine facing (which is where the air screws are on this carb)? Maybe it's just a weird carb talk thing. I guess you could argue that the air enters from the front of the carb, just weird terminology.

I may be odd on this one. I just can't call the exit flow of fuel and air the "front" of the carb as air flows through it from front to back. But I suppose you could say it flows BACK to FRONT *shudder* Although it faces the FRONT of the motorcycle, I can't bring myself to call the head side front.
 
MotorbikeBruno said:
I may be odd on this one. I just can't call the exit flow of fuel and gasoline the "front" of the carb as air flows through it from front to back. But I suppose you could say it flows BACK to FRONT *shudder* Although it faces the FRONT of the motorcycle, I can't bring myself to call the head side front.

Haha it's a weird situation for sure. I guess all of this would have been solved if they hadn't made engines backwards in the first place... Put the carbs on the front of the bike, and the exhaust on the back, and we're all on the same page ;)

Note: I know this has been done before, and I know there is a reason engines are built the way they are. I'm just messing around.

Glad we got this all cleared up before I started richening the mixture thinking I was leaning it out!
 
treitz said:
Haha it's a weird situation for sure. I guess all of this would have been solved if they hadn't made engines backwards in the first place... Put the carbs on the front of the bike, and the exhaust on the back, and we're all on the same page ;)

Note: I know this has been done before, and I know there is a reason engines are built the way they are. I'm just messing around.

Glad we got this all cleared up before I started richening the mixture thinking I was leaning it out!

Truth! There's been a few cool carbs out front motorbikes on here :) they fixed it! haha.

Always good to be cleared up before we start adjusting things :)))))))
 
Back
Top Bottom