Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Hey guys I am almost done my build but I can't seem to get the clutch adjusted. I have done the adjustment as per instructions I found on DTT and a few youtube videos but I just can't seem to get the clutch to engage. I am wondering if there is a way to test the clutch? A way to force engage it...
Hey guys finally got my bike running after a complete rebuild and there appears to be an oil like from behind the tach housing. Can anyone tell me if I can remove that housing to replace the gasket without causing any issues?
Hey guys, I mounted my front wheel today and things just didn't look right to me but i have never built a cb350 before.
The bike is a CL350, but i have swapped the forks and lower and upper triple with a cb360. The thing that didn't look right to me is the space between the fork and the break...
Hey guys I got my lower forks powder coated and they got a small bit of paint on the inside. It is just at the very top on the lip where the deal sits and a small bit in the inner tube at the top. Any idea if this is going to cause any issues? Should I try and scrape it out?
Hey guys, I few weeks back i did a post in the suspension section but I am still trying to come up with a definitive answer to this question and I know this section gets alot more eyes on it.
Does anyone know if you can add the external fork springs from an older CL 350 to a set of newer CB...
Hey guys, is it possible to run the external CB350 fork springs on the new CB forks with the internal springs? I really like the look of the external springs but my bike is setup with the newer forks.
Hey guys, I am trying to swap my forks on my 70 CL350 over to some newer CB forks. The forks I had were in rough shape and also didn't fit the new triple tree I bought. I have picked up a new set that are in decent shape, but there are some subtle differences and now I am wondering if there are...
Hey guys, I need to order a new flip style gas cap for my 350. Any recommendations on where to pick a cap and latch up? Took a look on eBay but they are really expensive.
Hey guys just pulled my forks apart to replace the fork seals, they are the older style with the tapered top. Seems to me that way this style stays under pressure from the spring they might be hard to get back together.
Does anyone have any tips before I get started on the reassembly.
Hey guys can anyone tell me what all needs to be changed when putting a 1969 cb350 camshaft into at 1973 cb350. I am asking because I bought at engine today with the intention of using it as a parts motor. When I went to pick it up and told him I was thinking of using it as a parts engine he...
Hey guys, anyone got any tips for getting the lower swingarm bolt out? I got it to start to come out with some force but doesn't want to move at all now. I can still turn bolt using the nut on the other side but other then that I can't get it to move at all.
Hey guys, I pulled off the side cover of my engine today to polish it and found a few things hanging out under the filter on on the lower right side.
If you have a look at the images, I think most of the black stuff is a ground up rubber. but there was also what looked what might have been a...
Hey guys looking for a 1970 CB350 k02 Gas tank. Ideally something in not too rough of shape. I don't mind doing a little bond work or paint but I want to avoid having to deal with a lot of rust inside.
Hey guys, been reading through a ton of post on tire selection and seems like the Bridgestone Spitfire are one of the most recommended
tires for the CL350. I am little new to all this so before i go ahead and make the order I wanted to get a second opinion.
Here is what i am thinking...
Hey guys this is my first cafe project so i am a bit of a newbie. I am trying to figure out if I need to replace my front forks. I know that I will have to do the seals either way but I not sure bout the chips in the casing.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.