Search results

I've built a 378 out of my cb360. I bought some Mikuni 30mm flat slides. Looking for a base line for jets. Edit: I was dumb. They are Keihin PWK30

I really want to install this pair of flat slides on the 360. I'm having trouble finding a cable or someone to make them. Motion Pro quoted me $175-$325 for chrome cables which I find ridiculous. I started thinking about snow mobile cables cause they have to 1 into 2 setup. Mikes XS has one...

So I was thinking about making some pipes. I'm going to a lot of troble to build this engine, i want pipes too. I decided it would be better to start with science to get me in the ball park and move on to the art of pipe building from there. Unfortunately, there are many values I don't have and...

My former integrated LED tail light failed when the rear wheel bounced from a pot hole and impacted it. It seems the best way to replace it was to cut off more of my tail section, build a new seat, and build an integrated wire harness too. ??? I've had trouble with the turn signals working...

So yesterday I decided it was a good idea to rewire the CB360. It's minimal, no clocks, no idiot lights, no starter. Already wired up is: regulator/rectifier, kill switch, coils, turn indicators, flasher relay, and alternator. I'm having trouble with a few wires from the left hand controls. I...

There was one episode where Bugs Bunny jumped on a bike to get some where in a hurry. I haven't seen the episode in years, and i can't find it now. The scene was only a few seconds long, and i think he left the bike to get on a plane. I'd like to find the episode, or at least an image. The bike...

I've been having trouble with my spark lately. I remembered I have a Cornwell multi meter that can check dwell. Checking dwell is the only way to make sure that both points are set identically, I just never worried with it because she ran fine. The way I remember setting dwell on my old truck...

Before you get too excited, the engine is stock and worn out. I've got some K&N filters and pipes. Most of my performance came from removing everything that didn't make it go or stop or pass inspection. My estimate when they pulled it in was 25 horse power and 15 ft torque. I was surprised on...

My uncle gave me this 77 cb750. It's complete and he says it ran when he parked it. I have a couple or 7 projects already, but recently I had the idea to build an e-production race bike. This would be a good candidate for that. Or I could sell the parts and make a little scratch to fund my...

My dip stick on both my 360 and 350 say 2 quarts 10-40. but at a quart and a half the stick reads full. So I always only added that much. I even tested it while running wondering if it made a difference in the reading... It does, it's un-readable. I don't want to cause any undu damage. Should I...

I know the 850 pistons fit the 360 perfectly. but now I'm trying to build a SL350 and I would like to use some thing like the gs850 pistons. They are lighter among other benefits. but I don't know if the wrist pins are the same or if the stroke is different enough that it won't work. thanks...

Last year was our first big event and was a great success. So we are doing it again. September 10 2011 is the second annual Run to the Sun. This is a Mods vs Rockers gig. So tell the scooter chicks too. Registration starts @ 9:30 am @ Otherlands on Cooper. We leave from there for a ride...

I've had these carbs brand new in the box for a couple of years now. I decided one day to put them on the 360. It runs really rich. But still impressive. The shop I trust to tune them is going to be expensive. So I thought I would give it a shot myself. Can you guys give me a starting point...

My brakes are... inadequate. I need an upgrade. What will bolt on or nearly bolt on? I'm not scared to make stuff. But I want to keep my forks. I believe these brakes were used on many mid seventies Hondas. Better caliper and rotor is what I'm look'in for. Also, I have been searching the web...

I bought this bike for $200 because the guy thought the gear between the crank and tranny was broken. It turns out the clutch was adjusted wrong and was always dis-engaged. After I cleaned the parts, lubed the cable and adjusted everything, sometimes when i pull the clutch all the way it would...

The Memphis Mummies motorcycle club is hosting it's first benefit ride on Saturday September 11, 2010. We will meet @ Otherlands at 10 AM for coffee. leave for Shelby Forrest @ 11, then to Sun Studios @3-4 for free tours. then we roll down the street to Kudzu's for a bike show and music...

The Memphis Mummies motorcycle club is hosting it's first benefit ride on Saturday September 10, 2011. We will meet @ Otherlands at 10 AM for coffee. leave for Shelby Forrest @ 11, then to Sun Studios @3-4 for free tours. then we roll down the street to Kudzu's for a bike show and music...

I didn't know where to put this. I figure this is the only place a moderator won't yell at me for it. A good friend/ near brother (and DTT member) lost this job yesterday. He is a very skilled motorcycle mechanic and custom bike builder. He can also ride the wheels out of anything. I have...

I traded some used tires that were taking up space for this 1982 CM250. This is what it looked like when I unloaded it. That's a straight bar. It's a little uncomfortable. A drag bar will probably happen. Maybe a riser with 3" pull back. But first, the wiring. I spent too much time...

I have a Jawa 477 that I'm molesting into a cafe/bobber. It has a 6 volt system and I have been unsuccessful at locating a tail light I am happy with. I would love to run LED, but i know this is not possible due to the 6v system. For the few of you that know the 477, I plan on mounting it...