Search results

I am looking to replace my stock cb160 speedo. It is old and crusty and I am not looking to drop $100 bucks on a used stock one to replace it. I wouldn't mind making up a oval shaped plate and drilling a hole in it to mount a nice mini round speedo and then do the indicator lights on the...

Tried honing my jugs but in order to clean them up fully I will be out of spec for the std size pistons. I have a set of STD size pistons with fresh new rings. $80 for the pair? or best offer. Text me: 260-417-4789 Located: Fort Wayne, IN Will have a pic to add later.

2 x Rebuilt Keihin 3-D Carbs (All new gaskets, jets, perfect diaphragms, etc) Bags of new parts, gaskets Sirius consolidated jet kit and case! + additional jets purchased from ebay. 70/71 110/115/120/125/130 jets TONS OF JETS! Spare diaphragm, float, remnants of at least 4 rebuild kits, tons...

1975 CB125 single for sale: This is what I have done to it: Fabricated electrical compartment onto air box (no side covers needed) New Tires (Michelin gazelle) Rebuilt Carb custom exhaust painted with high heat black paint. Cb100 front wheel Chopped Rear fender Start of a seat pan Painted rear...

I am in the process of getting this carbs to work. I figure with some jetting changes they should work fine. First question is if the stock rubber mount boots from a cl350 would fit on the cb360? The boots I currently have on my cb360 engine are too large.

I am working on my cb125 and got the idle fixed and can get it to idle smoother now. But when I go to ride it has no power and dies out with any acceleration. Is this a jetting issue? Bike rides when I have the idle set super high (4-5,000) but I know thats not good for it.

I have a bunch of cx500 parts. CDI Ignition Carbs with boots Radiator Wheels Forks Final Drive Shaft Swing Arm Engine (needs cam chain work and rebuilt) Frame I am located 46805 so shipping large items maybe pricey. Post or PM me and we can work prices

I am in need of a KZ200 tank and a Carb. P61B Keihin stock carb works.

I have a set of carbs off a cb360 with good diaphrams. I bought gasket rebuild kits for them so all rubber seals are provided. Carbs just need cleaned and reassembled and jetted to your liking. 50 Shipped?

I have here the first model year for the XS1100. Bike was titled, running, riding only 2 years ago. Great bike with a little TLC Bike needs: Starter work wiring checked Tank Cleaned Rubber Carb mount boots Asking $700 Trade for a good runnning/riding pre-1983 Honda/Yamaha (CB or XS...

I have been having trouble with my cb125 carb. Tried cleaning my carb more and found this: I was wondering where does the fuel draw from for the idle circuit? Should there be a hole in this seemingly plug? I have been having problems with idle and when i turn the air mixture screw nothing...

I have myself a 1975 CB125 When I first got it I couldnt get it to start with out the choke being on so I pulled the slide and the needle was set on the leanest setting. I dropped the clip down each notch until I could get it idled low with out the choke. Still after all that it was running...

This is the style petcock I need for my 1975 cb125 Mine was missing tubes and the top boss going into the tank for the tubes got chipped my PO. Mainly need a body with tubes but I will take a whole one.

I am in need of some calipers to measure and see if they can be retrofitted via bracket to a cb125/cb200 to convert the calbe driven to a hydraulic. Probably only needs to be single piston but some small dual pistons might work. Not looking to pay for much just looking to get some donations...

Not sure if there is anything posted about a good source for LED replacement bulbs but I just used ledlight.com and bought a 6v led tail light bulb for my cb125s and it was super reasonable and the bulb is great.

Got this bike off a curb here in town. Destined for the scrap yard I intervened. Most the bike was there but needed some TLC. Products I use; Rust Remover - Workshop Hero Rust Bath (http://www.workshophero.com/de-rust-motorcycles.aspx) Paint Stripper - Rustoleum Aircraft Remover...

I have a 1975 CB125s and I need a pair of side covers to button up my project.

I believe my bike is a 1975. Missing the lower float bowl. Would like a whole carb possibly for parts. Not looking to spend too much. Can trade some machining type of work. Depends on what you need done. email me: xedstatemanx@aim.com

I am in a need of working cb360 carbs. Bike is complete minus a tank and carbs. Really want to get this running to sell. Not looking to break the bank since I will be selling this bike soon