Search results

I'm toying with the idea of selling my latest bike to fund a new project. I picked her up late last summer. It has 30k on the tach. Runs like a champ, after rebuing the carbs last fall. Also threw on new tires at the end of last season. Basically I did all the tricky stuff to get it running...

I just picked up a 76 CB550 Super Sport, it came equipped with a massive King and Queen seat. Any of you know what stock seats would fit? Other than the same year and model. They seem to be hard to come by.

I am going to ditch the battery on my 72 CL350. I was wondering what type or where any of you who have done this purchased your capacitor? I have seen a few posts on other forums but nothing to concrete I have seen from 4500uf to 40000uf. Any help would be much appreciated.

I was cleaning my garage after a long winter and I found this. I really have no excuse not to be riding this heap in a month or so, well besides money and motivation. I have a month to go and I will be taking my state electrical journeyman's test. It's the culmination of 4 years of an...

Here she is, I had a build thread I started a years or so ago. I really lost my focus late last fall, it got pretty cold quickly last year and the garage seemed like the last place I wanted to hang out. Between family, work and whatever else time passed quickly and I finally figured out how to...

I just snapped the bolt off the back of my speedo. I wasn't too keen on opening up my speedo to try and pull the bolt. Any ideas or suggestions would be greatly appreciated.

Here is where i started, the now normal florist foam. Also a healthy dose of hope that this would be a breeze. I used an old hacksaw blade I had lying around to make some cuts before I started shaping with a sanding block. It easily started to take shape. I decided when I was mocking up the...

I am starting to build a fiberglass seat. This is my first and hopefully only attempt. I have made my foam model and I going to pick up materials tonight. Here's my question. How many layers of glass matt are you using? I can only assume more than one. I plan on starting with a fleece base but...

This is a before shot to show the starting point. Here we are now. Really a mid point , now running some mods nothing major (long winter ahead for the bulk of the project) Headlamp relocation. CL exhaust with some shorty mufflers, picked up on the cheap. Seat. Welded with a lot of help from...

I just cracked open my alternator to turn my engine over to adjust my points and oil came out. I don't have a clue what is going on. Anyone?

This weekend I am heading out to a local motorcycle wrecking yard I was wondering if anyone could suggest any bikes that might have rear-sets that would bolt on? I am running side pipes and I don't think that will be a problem with clearance. Any help would be sweet. Thanks Dan

I have a CL350 I am thinking about going with a bigger tank. Will a CB tank fit? This may be mundane question and if I searched I would probably find an answer here but any help would be nice. Thanks Dan.

I have recently put all new gaskets on my CL350 carbs, new fuel line, and cleaned the petcock. Yet still no fuel into the bowls. If I remove the fuel line gas comes out I can see it in the in-line filters. It just seems none is making it in to the carbs. Is it possible to have some suction that...

I have a 72' CL350. I am getting spark on one side but and none on the other. According to the Clymer manual I should be getting a "fat blue spark". I got a little wimpy one and nothing on the other. What might be my best course of action for sorting this problem out.

Can anyone tell me if a CL450 tank will fit on a CL350? There is a guy selling one locally, rather cheap and I would like to know if it would fit before i buy it.

I have a 72 cl350 that needed new float bowl gaskets. The local Honda shop had a gasket kit with all the gaskets/ o-rings needed to rebuild. There was one small washer included with each kit. I haven't the slightest idea where this goes. If anyone could help me that would be great.

I need some rear fender suggestions. I have a 1972 CL350 and would like some pictures of what some of you guys may have done. I am using the original seat pan to build my seat if that helps. Thanks

Could anyone tell me what size bolt attaches the brake arm to the drum on the front drum of a CB/CL350. I am a retard and lost it.

I have a set of bikemaster clubmans but was told only to drill them out for the control set screws and not to pull wiring through them. Anyone else heard anything like that?

I'm Dan from Minneapolis. This is my 72 CL350. This bike has been haunting my garage for the last three years. I've finally gotten around to digging into it. I had started with a 72 CB500/4 but I have since sold it, after some serious lack of motivation, which now focuses all of my attention on...