Search results

hey guys looks like the mz café isn't going to be finished for the summer so I bought a Daelim daystar 125 locally for couple of hundred quid. It'll get me on the road and should make a fun commuter once it passes its road test. Of course being an arse I immediately started thinking about doing...

well been a while since the bike got any attention, anyway after being advised the exhaust from a large cc four stroker wouldn't do a small cc two stroke any favours. so I managed to get one half of an rd250/350 system off ebay cheap. unfortunately its the left hand pipe and the mz exhaust port...

basically i have a karcher hds 501 which needs two new electrode caps. Not sure if thats an accurate description, basically the there are two spark plug looking things that ignite the diesel to create the steam. The metal caps that connect the ignition wires to them are badly corroded. Karcher...

had a look on the gasgas forum, looks like i'll get plenty of good technical advice there. Have been given a plastic tank and matching seat off a KX scrambler. however I'd rather modify the tank to fit the frame than hack up the frame to suit the tank. question is how difficult and expensive is...

have spent a week searching every ebay and gumtree site in Europe and haven't found a single pampera for breaking. I'm thinking of fabricating a tank out of metal or possibly grp and a basic tracker style seat. Maybe stick a round light on the front and remove the rear fender. Basically give it...

hey guys I'm in the middle of a small two stroke engine café build and was out hunting for 35mm forks (the old stanchions are shot) when I was offered the ones off this for £50 on the condition that I took the whole bike. tank, seat, rad guards and bars are missing, on the plus side she was a...

thanks for the advice guys, not a big deal to pre mix, just thought I'd look into the alternative.

thanks for the advice xb33bsa, its an MZ ts150.

hey guys how hard would it be to make a pre mix two stroker into a self oiler? has anyone done this, sorry if its a daft question.

cheers Ryan, not much done this week, but thanks to the do the ton members I managed to fix a little issue that was bugging me. How to stop the kick start from fouling on the new foot peg position? (tacked on the old pinion pegs to work out rearset location) Anyway.... Old non folding kick...

hey guys there is a 'new/arc plasma cut 40' on my local ebay with no bidders yet as the description reads...."Plasma cutter stopped working today- i think its the spark generator- everything works but no spark, I'm sure someone can fix it, comes with torch and earth lead." Round here a new...

got a few hours done on the bike today, doesn't look like much but re made the brackets that hold the tank on, rubber mounted front and back which makes me feel much safer. Also had to cut and re weld the frame under the seat to get a better fit. drilled and fitted the new top bushes for the...

Looks like the same list, from the same site. I'll delete this thread, no point in doubling up on the same information. cheers for pointing it out.

Found a link to this page from another site while looking for alternative 35mm forks for my bike. Might already be on here, or even created by a fellow dotheton member, whoever gathered this information may thanks...

cheers guys, i'll look out for a pod filter for now, and then look at the exhaust.

You guessed it jungalist! 150 cc of pure comuter crap. I'll have a look for that info stroker crazy. Cheers guys

hey guys I need some advice on tuning my 150cc 2stroker. I'm still in the middle of the basic fabricating stage but for space reasons I need to work out what type of air filter I want now. I want to fit either a cone filter or a pancake job, but don't know how these will effect the bike. The...

not much progress due to work, but picked this up off ebay for pennies :)

thanks for the advice guys, i'll keep an eye open for a voltmeter to fill the hole instead. thanks again.

hey guys I have replaced the old ignition barrel on my mz with a more modern Suzuki item. the old one was mounted in the headlight in front of the speedo. so what to do with the hole? I have an old ammeter and oil gauge that I salvaged from a boat. I'm thinking maybe I can fit one in the...