CresentSon
Over 1,000 Posts
Re: Time to make the rd look like it runs haha
Yup, looks tough, like it wouldn't flinch from a Chuck Norris crotch kick.
Yup, looks tough, like it wouldn't flinch from a Chuck Norris crotch kick.
THE RD FROM HELL
- Thread starter bradj
- Start date
CresentSon
Over 1,000 Posts
Re: Time to make the rd look like it runs haha
If you run out I'll send you a couple to grind on. I find letting you vent is beneficial to the surrounding population.
If you run out I'll send you a couple to grind on. I find letting you vent is beneficial to the surrounding population.
JustinLonghorn
No Purple Hearts, No Blue Ribbons
Re: Time to make the rd look like it runs haha
Ha!
Ha!
JiveTalkinRobot
Been Around the Block
Re: Time to make the rd look like it runs haha
Im a bit jealous I don't have your skill set...
I wish I could build like that and not have to buy eBay parts etc...but Im already having a bitch enough time installing "store bought" Moto Carrera rearsets.
One day, I will be worthy of this forum...one day...maybe the next bike.
Im a bit jealous I don't have your skill set...
I wish I could build like that and not have to buy eBay parts etc...but Im already having a bitch enough time installing "store bought" Moto Carrera rearsets.
One day, I will be worthy of this forum...one day...maybe the next bike.
cyclefreak
Over 1,000 Posts
Re: Time to make the rd look like it runs haha
Looking great man.
Looking great man.
Re: Time to make the rd look like it runs haha
The gas tank is sectioned and welded out i still have to put air to it and try to seal the leaks (there is gonna be a few im sure)
Next is the oil tank planning. im still not 100% on how im gonna run the line,vent, fill neck, sight glass and fasten it to the gas tank clean. but im not gonna let that stop progress i spent a little time on resizing the front axl. But all and all its moving right along.
The ta do list is still pretty big
Oil tank build
18 inch Front wheel lace
Buy tire
Rotor spacers
Oil pump rebuild and side cover swap
Possible yz swing arm swap
lil battery box & hide electronic's
Head light ears
steering dampener mount
Seat and tail build tail light snd tag mount
French in mini speedo in head light bucket
Converting carbs to run premix???????
Get car coils
Electronic ing and rev limiter
Body work and paint
Telling my self this is the bike
i should have built to begain with
Ya gotta want it
Sent from my PB99400 using a recorded womans tennis match turned up all the way & cheap 80's skin books to forfull a nights agenda
The gas tank is sectioned and welded out i still have to put air to it and try to seal the leaks (there is gonna be a few im sure)
Next is the oil tank planning. im still not 100% on how im gonna run the line,vent, fill neck, sight glass and fasten it to the gas tank clean. but im not gonna let that stop progress i spent a little time on resizing the front axl. But all and all its moving right along.
The ta do list is still pretty big
Oil tank build
18 inch Front wheel lace
Buy tire
Rotor spacers
Oil pump rebuild and side cover swap
Possible yz swing arm swap
lil battery box & hide electronic's
Head light ears
steering dampener mount
Seat and tail build tail light snd tag mount
French in mini speedo in head light bucket
Converting carbs to run premix???????
Get car coils
Electronic ing and rev limiter
Body work and paint
Telling my self this is the bike
i should have built to begain with
Ya gotta want it
Sent from my PB99400 using a recorded womans tennis match turned up all the way & cheap 80's skin books to forfull a nights agenda
stroker crazy
crazy as a fox
Re: Time to make the rd look like it runs haha
Sometime act first, plan later, gets the job done!
But .... why do you have 'converting the carbs to run pre-mix' on the to do list?
Crazy
Sometime act first, plan later, gets the job done!
But .... why do you have 'converting the carbs to run pre-mix' on the to do list?
Crazy
stroker crazy
crazy as a fox
Re: Time to make the rd look like it runs haha
I asked because I am going to attempt to use FCR's on the RaZoR.
Crazy
I asked because I am going to attempt to use FCR's on the RaZoR.
Crazy
Re: Time to make the rd look like it runs haha
make a low spot in the floor of the oil tank and then drill through that and the fuel tank and insert a short length of tube and seal around it. That will be the oil feed. try to get it as flush as possible with the floor of the oil tank. Replace the tank section and fit a vented flush fit filler cap. No sight glass, low oil level light etc needed.
Drill and tap the carbs manifolds or reed boxes (your choice) for a small threaded barb or vacuum fitting for the oil feed from the pump.
Job done. Check oil by opening cap, every time you fill with gas and top up as required.
make a low spot in the floor of the oil tank and then drill through that and the fuel tank and insert a short length of tube and seal around it. That will be the oil feed. try to get it as flush as possible with the floor of the oil tank. Replace the tank section and fit a vented flush fit filler cap. No sight glass, low oil level light etc needed.
Drill and tap the carbs manifolds or reed boxes (your choice) for a small threaded barb or vacuum fitting for the oil feed from the pump.
Job done. Check oil by opening cap, every time you fill with gas and top up as required.
650hardtail
Been Around the Block
Re: Time to make the rd look like it runs haha
ill take a look at the ds7 engine i have.. pretty sure oil is injected into cases not carbs.. i know the 74/75 h2 had oil fittings into carbs-also into cases for main bearing lube..
ill take a look at the ds7 engine i have.. pretty sure oil is injected into cases not carbs.. i know the 74/75 h2 had oil fittings into carbs-also into cases for main bearing lube..
