THE RD FROM HELL
- Thread starter bradj
- Start date
650hardtail
Been Around the Block
Re: Time to make the rd look like it runs haha
saved me a trip to the shed..thanks
Redbird said:
saved me a trip to the shed..thanks
Re: Time to make the rd look like it runs haha
On a 400 the oil pipes go to a special drilling on the lower front part of the carb just before the reed boot. Piston port motors are drilled at the side of the boss where the intake manifold bolts on. That applies to DS7, R5 and TD3. The oil feed can also go into the float bowl as is done on some Kawasakis or into the reed cage.
Try to avoid having them discharge into still air for example above a dead zone or to teh sides where there's a ribber intake stuffer obscuring them..
On a 400 the oil pipes go to a special drilling on the lower front part of the carb just before the reed boot. Piston port motors are drilled at the side of the boss where the intake manifold bolts on. That applies to DS7, R5 and TD3. The oil feed can also go into the float bowl as is done on some Kawasakis or into the reed cage.
Try to avoid having them discharge into still air for example above a dead zone or to teh sides where there's a ribber intake stuffer obscuring them..
Re: Time to make the rd look like it runs haha
So i mentioned a junk yz a few post back well here is the skinny the chain was on the wrong side on that bike god only knows why that was a good idea. Im toying with losing the dirt bike mono crap and flipping the swing arm so the chain clearence stuff is on the side god wanted it and adding twin shock mounts i also need to take a little out of the now underslung brace i think i need to distroy one hand made alum swingarm to build another due to some one off parts ive already had made for the first rig so sorry redbird the old one is not on the market its under the knife but ill build ya one for some clubmans and dinner if your not in a hurry
This swing arm if i can pull another rabbit out of my hat will allow me to run a rear disc spoked wheel that i want to build
Ya gotta want it kids
Sent from my PB99400 using Tapatalk 2
So i mentioned a junk yz a few post back well here is the skinny the chain was on the wrong side on that bike god only knows why that was a good idea. Im toying with losing the dirt bike mono crap and flipping the swing arm so the chain clearence stuff is on the side god wanted it and adding twin shock mounts i also need to take a little out of the now underslung brace i think i need to distroy one hand made alum swingarm to build another due to some one off parts ive already had made for the first rig so sorry redbird the old one is not on the market its under the knife but ill build ya one for some clubmans and dinner if your not in a hurry
This swing arm if i can pull another rabbit out of my hat will allow me to run a rear disc spoked wheel that i want to build
Ya gotta want it kids
Sent from my PB99400 using Tapatalk 2
Re: Time to make the rd look like it runs haha
The junk yz and the sheet of steel puts my remodel to a grand total of 37 bucks and three rare gas tanks that i distroyed
But dont worry guys im just getting warmed up i may break a. c-note haha i will end up dropping some money im just using shit that ive been gathering up for two years now several 13mm spacers and custom bla bla one off will start soon
The junk yz and the sheet of steel puts my remodel to a grand total of 37 bucks and three rare gas tanks that i distroyed
But dont worry guys im just getting warmed up i may break a. c-note haha i will end up dropping some money im just using shit that ive been gathering up for two years now several 13mm spacers and custom bla bla one off will start soon
Re: Time to make the rd look like it runs haha
i dig.
i dig.
MoToBoX-VintageSpeed
Active Member
Re: Time to make the rd look like it runs haha
exhaust is very tasty ;D
exhaust is very tasty ;D
