Dear Mark,woolsac said:Viet,
These look mint and at a great price. I have a CL350 and will probably end up ordering the full set. Just wanted to give a heads up.
Thanks!
Mark
Viet said:Dear Mark,
Many thanks for your interest. I am planning to set a side USD 3 for any sale on ebay to the people in difficulty in Vietnam. My friend organises a free lunch at hospitals in Hanoi and the money will go there as first destination
Thanks again
Please buy out of ebay for DTT discount. The price is 110 including the bracket.jgsb1966 said:hello viet! i am interested in a set of these for my '72 cl350 scrambler. how do i order them? or should i search for you on ebay and purchase them through there? interested in the rubber toe boots, hole for the brake light and the adapter plate for the cl350 too.
Viet, as mentioned I have a cl350, did you mail the additional bracket with my rear set and clevis order?Viet said:Dear Mark,
Many thanks for your interest. I am planning to set a side USD 3 for any sale on ebay to the people in difficulty in Vietnam. My friend organises a free lunch at hospitals in Hanoi and the money will go there as first destination
Thanks again
jgsb1966 said:hello viet! i am interested in a set of these for my '72 cl350 scrambler. how do i order them? or should i search for you on ebay and purchase them through there? interested in the rubber toe boots, hole for the brake light and the adapter plate for the cl350 too.
woolsac said:Hey JGSB.
Had a couple of questions in regards to your rearset install... provided you received the parts and started the work.
I received mine last week and have a couple of questions on the install that either you or Viet can provide guidance on:
1. The bolt to the rearsets when fitted on the rear passenger pegs are too long and hit the side of the rear wheel swing arm. Is it ok to cut off 1/4" to provide clearance from hitting the swing arm?
2. Is only one lock washer required for each side? 4 total were shipped and wasnt sure if I was missing a step of installation.
3. Did not know that this was not a complete install and ready to ride kit. There is no linkage to the shifter rod. I assume that I will need to cut up the original shift lever to connect the linkage to? Does anyone have any idea if there is an aftermarket part taht I could use that can do the same job? I always like to keep the stock parts in case if I ever want to go back to the stock settings and would hate to cut up my shift lever.
Thanks!
Mark
jgsb1966 said:i just received my rearsets today. only had a chance to look real quick at it tonight, but it looks like there is no possible way for the kickstarter to clear the brake pedal. am i missing something here? haven't looked at the left side, but i don't recall a linkage for the shifter, so it looks like i might have to cut mine. i'm a little frustrated right now, so i called it a night. lol! also, there was only one page of instructions that only covered a very little bit. how many pages were there supposed to be?
jgsb1966 said:here is a mockup of my rearsets and my kickstarter on my '72 350 scrambler. any suggestions, opinions, did i mount them up wrong (ignore the electrical wire i used to hold them in place and the kickstarter down)
My kick starter doesn't clear the brake lever either. I dont normally use the kickstart for I still have my electric stater installed. Also, I ran into the same issue with the linkage to the shifter. I bought an offset linkage for our CL's off of Dime City Cycle. Issue with that now is that the DCC linkage arm is too wide to fit in the provided linkage joint. I will have to sand down the aluminum on the DCC arm to fit in the joint. Not so much "install and go" as I thought it was going to be.... I'll keep you posted.jgsb1966 said:i just received my rearsets today. only had a chance to look real quick at it tonight, but it looks like there is no possible way for the kickstarter to clear the brake pedal. am i missing something here? haven't looked at the left side, but i don't recall a linkage for the shifter, so it looks like i might have to cut mine. i'm a little frustrated right now, so i called it a night. lol! also, there was only one page of instructions that only covered a very little bit. how many pages were there supposed to be?