Need help with Pamco ei please.

MrMister

Been Around the Block
DTT BOTM WINNER
Hi everyone. I think I’m having issues with my Pamco ei for my cb360. Possibly a fried capacitor or resistor. What’s the best way to find the culprit using multimeter?

When I put my ohm meter at 2000 through the red wire on the coil side and probe the magnet sensor, (from left to right) I get 1306, 441, and 1857 on one, and 001, 441, and 1853 on the other sensor.

If I tap into the black wire and probe the sensors I get… 546, 0, and 994 on left, and 1743, 0, and 995 on right sensor.

Green wire I get: 1092, 320, and 1655 on left sensor. And 1., 320, and 1653 on right.

White wire: 1091, 320, and 1650 on left, and 1., 319, and 1647 on right.

IMG_8031.JPG
IMG_8032.JPG



Sent from my iPhone using DO THE TON
 
I don't think anyone has had great success with electronic ignition on any version of the 360.
The area runs so hot it tends to destroy even the best electronics. (I know Pete switched to 'military grade around 2017)
I've been 'playing' with CB/CJ 250/360's since early 1980's and never found anything that keeps working. (I still have several, 5 or 6, mostly in pieces)
Look for how to test Hall Effect sensors first as it's cheapest thing to fix and probably most likely to fail
Could also be in need of re-soldering as the heat/vibration will cause problems long term, particularly if non-lead solder was used?
The magnets on rotor could also have gotten weaker?
Ceramic magnets can cope with a lot more heat than neodymium magnets which become non-magnetic if overheated.
Gap between sensor and magnet may also be too big, I don't know spec for Pamco but many flywheel magneto's require a very small air gap (Briggs and scrappem need 0.006" but won't tell you 'for free')
 
I don't think anyone has had great success with electronic ignition on any version of the 360.
The area runs so hot it tends to destroy even the best electronics. (I know Pete switched to 'military grade around 2017)
I've been 'playing' with CB/CJ 250/360's since early 1980's and never found anything that keeps working. (I still have several, 5 or 6, mostly in pieces)
Look for how to test Hall Effect sensors first as it's cheapest thing to fix and probably most likely to fail
Could also be in need of re-soldering as the heat/vibration will cause problems long term, particularly if non-lead solder was used?
The magnets on rotor could also have gotten weaker?
Ceramic magnets can cope with a lot more heat than neodymium magnets which become non-magnetic if overheated.
Gap between sensor and magnet may also be too big, I don't know spec for Pamco but many flywheel magneto's require a very small air gap (Briggs and scrappem need 0.006" but won't tell you 'for free')
Thanks Peter. I think i definitely fried something while putting a jumper pack on the battery. Because i fried my anti gravity battery too and had to replace it. Ill check out the hall sensors first. but in the mean time, i have the stock points back on and running like a champ.
 
Not sure if anyone has had a lot of success using lithium batteries on 360's, even with new alternator and R/R?
I know a few have had batteries catch fire when load balance inside battery can't cope with wrong voltage input, makes me afraid to even try one (as much as I would like to)
 
Not sure if anyone has had a lot of success using lithium batteries on 360's, even with new alternator and R/R?
I know a few have had batteries catch fire when load balance inside battery can't cope with wrong voltage input, makes me afraid to even try one (as much as I would like to)

Thanks. I’ve had the anti gravity in for 8 years now without any issues. I did downgrade to a cheaper brand this time which is making me wary from what you’re saying.

What’s the consensus with spark plugs on 360’s now? Since it’s impossible to find non resistor plugs, is it ok to use resistor plugs and swap out to non resistor caps if it’s still 5 ohm total?




Sent from my iPhone using DO THE TON
 
Yeah, thats the thing about lithium batteries. They work great right up until they don't. And once you notice there's something wrong, it's too late to do anything.

I spent an exciting afternoon watching a battery in my 851 melt down. That's the day I discovered a stock tool kit won't remove the fairings on an 851 so you can't even get to the battery to cut it out and toss it as far away as possible as it's doing it's smoke show. Will it burn? Won't it burn? Stay tuned for the exciting conclusion! No, it never actually produced flames, just impressive arcs and a metric schmidt ton of some of the foulest smelling smoke known to man.
 
Original Honda plug caps 74~77 were 10K not 5K so I would use 5K plug plus 5K cap.
I bought two boxes of B8ES several years ago plus have a pair in Honda /NGK boxes that came with one of my 360's.
The 'Honda Genuine Parts' are 51 years old so I keep them for display..
 
Back
Top Bottom