Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Re: 1971 Honda CB350 $1000 - Plymouth MI
If it comes to that I will let you know. Would really like to sell it to someone who can make it run again, shame to see it die :(
It is OBO!
Hey guys and gals, it's time to sell my old cafe project
1971 Honda CB350 twin Cafe Project
currently non-running, selling as-is. You get the bike along with all the extra parts I have for it. I did a complete down to the frame restoration on this bike, rode it for a few years, then started...
Been doing some more carb fiddling. Going to the 30 pilots helped my off-idle stumble (but it still will a little when cold, but much better). I was also chasing all sorts of idling issues. When it was cold it would idle rock steady at 1500, then once warmed up it couldn't idle at all. Turns out...
Glad you enjoyed it! There's a ton of info floating around this site so you're in the right place!
I leaned out the needles 2 positions Saturday and also built a baffle for my exhaust (it was ridiculously loud). Put about 80 miles or so on it this weekend and getting better mileage, mid 40's...
Re: Black and Gold Cafe - 71 CB350 - VM30's!
Current Carb settings (only idle tuning has been done):
pilot 25
air jet 2.0
air screw: 1.25 turns out
Slides 2.5
Needle 6F4
Needle clip 4 (1 lean, 5 rich)
needle jet P-0
Main 150
Current running issues:
low mileage
slight smoke on heavy throttle...
Re: Black and Gold Cafe - 71 CB350 - VM30's!
Finally!! It's running and riding well!!
I got the new ignition on and after getting it timed I was able to get the idle to settle down. I actually had to trim the base plate in order for it to be advanced enough, it appeared that the cut-outs were...
Re: Black and Gold Cafe - 71 CB350 - VM30's!
Well, I got the replacement transistors yesterday, and soldered them on without any problems. I mounted the old circuits to the board, and then cutoff the old transistor. I did this do I would know for sure that everything was oriented correctly...
Re: Black and Gold Cafe - 71 CB350 - VM30's!
Well...I got the dual pull-cable throttle all put together and working. It works great so far, nice and smooth pull, fast and snappy return, everything seems fine. I used a Norton (I think?) dual pull cable throttle assembly from eBay, along with 2x...
I used the same MIG trick on my throttle cable, and that broke too :(
I think DCC has shortened clutch cables that might work for you?
I used MTB parts to make my new custom throttle cables, but I'm not sure if those cables are up to the task of pulling the clutch. Although they are both...
Re: Black and Gold Cafe - 71 CB350 - Tires!
I used the 2-1 throttle cable kit from DCC and put my own ends on it. I didn't have the nice solder on ends, so mine were a little sketchy. I used crimped small fittings for the carb side, and a steel hitch pin for the twist grip side with a spot weld...
Re: Black and Gold Cafe - 71 CB350 - Tires!
Well, I made some progress and then broke some stuff.
I spent Saturday morning tinkering, and finally got it idling correctly. My problem up until now was it would idle fine for a minute or two, then just take off to 5-6000rpm. I did some searching...
Re: Black and Gold Cafe - 71 CB350 - Tires!
Here's the zip tie method:
http://www.youtube.com/watch?v=S6WPzRRJLpA
I had to use a pry bar to get it the last little bit of the beads over the wheel. Also make sure you zip-tie your tube inside the tire before mounting. I don't know if I would...
Re: Black and Gold Cafe - 71 CB350 - Tires!
Got the rear tire on, tried to go out for a test ride, and the damn thing is running like crap again. I'm not sure why the carbs go to shit after sitting for any more than a day, but it's really starting to bug me. Plan for tonight is drain the tank...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.