Search results

I have a pair of stock Keihin's off of a CL350 that I am attempting to rebuild. When I pulled them, the slides were stuck as well as the throttle butterflys (not sure if that's what they're called, but its the piece where the idle speed adjustment screw is and it's what lifts up and down when...

Looking to buy a decent CB350 tank from 1968 or 1969. Need something with no major dents or excessive rust problems. PM if you've got one and what you're looking to get for it. Posted an example pic below of the style of tank I'm looking for... Doesn't need to be in that good of condition...

Can anyone recommend a decent spoke kit for a 72 CL350? They ran a 18" rear wheel and 19" front... I know DCC has some kits but they're pretty expensive. I did a little shopping around on ebay and found some kits from china for like $75 shipped for both wheels. DCC was gonna be over $200 for...

I'm about to install the cam on my 350 and i have a question about valve timing. I know that the rotor has to be on the LT mark and the cam sprocket needs to be aligned with the gasket surface. This should put the left piston at TDC on it's compression stroke. HOWEVER my question is this: how do...

This probably a stupid question but I've looked all around the internet and my shop manuals and am utterly stumped. How the hell do I get the guts (spring + damper assembly) out of the fork tubes? I posted some pics below of what I'm working with. It seems like everything needs to slide out of...

Hey everyone, this will be my first build thread. I'm fairly new the world of bikes and have only worked on a few but I'm finally starting a project that I've wanted to tackle from day one. I'll try to keep this as short as possible and post as many pictures as I can. Today I picked up a pair...

Hey guys. Just sold my first bike, a 72 CB350 that i restored last winter. Now I'm looking for another project bike. I'd like to get another CB, doesn't have to be a 350. I'm ok with just about anything as long as its early 70s or even late 60 is alright too. Condition isn't all that important...

Hey everyone, Just got my 1972 CL350 up and running after spending all winter restoring it, now I'm just working on the fine tuning. It starts up and runs great, however I have noticed a popping sound on deceleration at times from the left side and sometimes while holding a steady speed like...

Just got my CB350 running and forgot to hook up the drain hose to the bottom of the bowl on the carb. I noticed a good amount of gas draining from the bottom of the carb out of what I believe to be a vent of some sort. Is it normal for gas to drain out of the carb like this? It seems like it...

Hi everyone, i'm pretty new here and new to motorcycles as a whole. I started reading the forums back in December when I picked up my first ever bike, a 1972 CL350 and all the information here has been super useful in helping me get it back in working order. I pretty much did the whole bike in...

I found these clamps that I think might work perfectly for mounting a cafe style seat to a frame. If you welded nuts into the inside of the flat part on the bottom of the clamp in the picture, clamp 4 of these to the frame rails, set the seat on top and then bolted it into the clamps through...

My CL350 pipes with mufflers, heat shields and all mounting brackets. Make me an offer. http://www.ebay.com/itm/261153524452?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

I just bought a replacement wheel of eBay to replace my old rear wheel. The brake shoe assembly from my old wheel fits into the new wheel, however when the axle is pushed through it causes the brake assembly to bind against brake drum wall just above the brake lining. It's not the brake shoes...

im looking to trade my CL350 Scrambler high pipes for a set of nice CB350 headers. The CL350 pipes are in good shape with a little surface rust that's not even visible when the pipes are on the bike. I attached a pic of them on my 350 below, but i can send who ever is interested better...