cb360 swingarm chop

Re: CB360 re-build.

Rattlecan said:
Great start brother, I'll be watchin.
Thanks!

I lowered it about an inch and I this looks a lot better imo and i think this is about as low it can reasonably go without a stretch. Thoughts?

IMAG0170.jpg


I like the stance here a bit better but as you can see there is hardly any clearance.

IMAG0171.jpg
 
Re: CB360 re-build.

I think the first stance is better imo, but I would get the front end set in place before you try and determine the stance as the ride height of the front end will help you better determine the stance and look you are after.

Remember its easy to move the front end up and down, from that point you can block up the frame as you have already and then determine your rear shock length and set the proper stance and ride height.

My advise to you is to work from the front back, thats the way i work and have had better sucess this way getting the look I want.

Keep up the good work.
 
Re: CB360 re-build.

Well I decided to see if i could lace the rear rim to the front hub and thus far everything has gone smoothly. The wheel hasnt been trued yet but it laced up no problem. I need to pull it apart again for cleaning and paint but I just wanted to make sure this was doable.

316403_10150319927673201_509343200_8053548_269396980_n.jpg
 
Re: CB360 re-build.


I did a bit of cutting/grinding/photo shooting today. The frame is basically done minus some miscellaneous mounting tabs that will get taken care of a bit further down the road.


DSC_0037.jpg



DSC_0035.jpg



DSC_0025-1.jpg
 
Re: CB360 re-build.


Back on two wheels!


Its nice when your friend, who's garage you are using has the same bike as you and lets you steal the wheels of his bike. We believe the tank is from a CB175. Its not fully mounted but I like the look and I'm thinking it might be the direction I go for the tank. The shocks arent contected because I was trying to dial in the stance. Im pretty happy with the way its siting just need to order some shorter shocks.


DSC_0012.jpg



DSC_0011.jpg



DSC_0031.jpg
 
Re: CB360 re-build.

So tonight I "mounted" the sporty tank and as you can see it looks ridiculous. Without the mounting tabs on the tank the only thing thats keeping it from sliding down the frame more is the spot on the backbone where the engine mount bracket bolts to. My first thought was to cut the wide spot out, slim the backbone up a bit and then not actually use the upper mount. I was lurking around looking at 350/360 chops and most of them had no upper mount so I think it aught to be fine. Thoughts?


DSC_0006.jpg
 
Re: CB360 re-build.

Hey bud,
You have to have a front mount on the tank. to keep it from bouncing up an down. Alot of guys hide the mount under the the front of the tank, thats why you dont see it. But they have a front mount for sure. You'll just have to get creative on how your gonna hide it.
 
Re: CB360 re-build.

Ive got a few ideas in mind on actually getting it mounted. Im going to do some some trimming this week and get the tank sitting a bit lower then see for sure on the mounting.

A question for those familiar with the stamped backbone. Do you think I could get away with cutting off a bit the seam/pinch welds on the top of the backbone and then just welding the 2 halves flush? It would make mounting this tank 300% easier.
 
Re: CB360 re-build.

Well I finally dialed in the stance. The swing arm is getting stretched 3in. Im putting in an order for a few parts to get this thing moving along.

428913_10150529626773201_509343200_8916736_1250500077_n.jpg
 
Re: CB360 re-build.

Are you going hard tail? I ask because your rear suspension is gonna be useless at that angle.
 
Re: CB360 re-build.

No hard tail. I know the rear suspension will be useless but Im ok with that. Im just a fan of the look.
 
Re: CB360 re-build.

Got my delivery form wrenchtechracing.com. Real nice pieces and Im thankful they were available as I dont have the access or ability to turn my own. Really pumped to get this swing arm stretched.

425191_10150548494953201_509343200_8970588_543342756_n.jpg
 
Re: CB360 re-build.

I got bored at work an whipped up a quick render of roughly what I want this thing to look like when its all said and done.

CBRENDER.jpg
 
Re: CB360 re-build.

Bert Jan said:
Love this pic! Dunno why, but it's really nice!

Thanks!

Well sense I laced my rear rim to the front hub Ive been hunting around for a new rear wheel/rim and I finally got one. So now I can order some tires and give my friend is wheels back.

Im going to be running Shinko 705s. They are cheap, different, and most importantly not firestones.
http://www.motorcycle-superstore.com/2/29/393/20401/ITEM/Shinko-705-Series-Dual-Sport-Rear-Tire.aspx

According to http://www.dropbears.com/u/utilities/tyrerim.htm I should be able to run 4.10x18s

Ive also been debating swapping out bars and running some flat trackers. Thoughts?

wheels.jpg
 
Back
Top Bottom