Father Son 75 CB200T Rise From the Ruins

Looks like a cut down GSXR/GSXF head, (SACS motor) lower hole in side is for rocker arm pivot
After looking at pics, I think Icould modify some of the 'mistakes' I made when cutting starter plugs to hold a Kawasaki EGR reed block?
 
crazypj said:
Looks like a cut down GSXR/GSXF head, (SACS motor) lower hole in side is for rocker arm pivot
After looking at pics, I think Icould modify some of the 'mistakes' I made when cutting starter plugs to hold a Kawasaki EGR reed block?
so that was your crazy idea?
 
Not my idea but I know they have been used to get high rpm 4 valve motors.
I'm pretty sure I have a spare head here but it's for 1100 or 1200 (I've been planning a monster motor for my 600 Katana ;) )
The 400 heads are pretty rare but would probably have the right size combustion chamber plus closer stud spacing as it was a completely redesigned engine
The bore/stud spacing is the same from 600 to 1200 as motor was originally designed as a 750 with some room for expansion - 600 is a small, overweight 750 ;D
 
What about these
a2a4e2e8.jpg



Sent from my iPad using Tapatalk
 
Giannini's CB77 based F250 motors. 2 valve per cylinder top ends like a GS500, so no rocker arms but only single inlet and exhaust per side. Have you found the CB450 top end on a CB77 bottom end that Pete Rhodes created a decade or two ago?

Fastest CB72/77 based motors are still those created by Jerry Koositra in South Oz.

For an 8 valve 200 motor a 200/250 top end or 4 cylinder 400 might work if it had enough fin area. Or weld a head or cast a new one. There are options - just above my pay scale though :-)

Maybe find a CR93 top end and graft that on. They flew as 182cc motors and could probably be stretched out to 200cc.
 
teazer said:
Giannini's CB77 based F250 motors. 2 valve per cylinder top ends like a GS500, so no rocker arms but only single inlet and exhaust per side. Have you found the CB450 top end on a CB77 bottom end that Pete Rhodes created a decade or two ago?

Fastest CB72/77 based motors are still those created by Jerry Koositra in South Oz.

For an 8 valve 200 motor a 200/250 top end or 4 cylinder 400 might work if it had enough fin area. Or weld a head or cast a new one. There are options - just above my pay scale though :-)

Maybe find a CR93 top end and graft that on. They flew as 182cc motors and could probably be stretched out to 200cc.
not yet I found a Suzuki DOHC head on a cb77 bottom... Thanks I will look that up! Is koositra Dutch? ;)


Sent from my iPhone using Tapatalk
 
There are options - just above my pay scale though :-)

So funny!

I wanna melt something. And they said building sand castles wouldn't pay off!
 
Maybe a SuzukiGS550 four head or Kawasaki KZ500/550 could be easier to modify?
GS500 is 74 mm bore so would be way too big for a 200 twin (they are below 50mm?)
Just had a thought, what about a VF400/500 head? ;)
 
Zeke's racebike for Ahrma...
udyhagyd.jpg
7 years away. We are getting more organized. We took a 1000 lbs rack and welded angle on the bottom with coasters. Now we can have the part bins with the bike and we can have two builds going at one time in our 9 by 15 shed.


Sent from my iPhone using Tapatalk
 
crazypj said:
Maybe a SuzukiGS550 four head or Kawasaki KZ500/550 could be easier to modify?
GS500 is 74 mm bore so would be way too big for a 200 twin (they are below 50mm?)
Just had a thought, what about a VF400/500 head? ;)
bingo GS 400 http://home.comcast.net/%7Eeholman/repspec.html
http://forums.sohc4.net/index.php?topic=22251.0
pypu6ety.jpg



Sent from my iPad using Tapatalk
 
crazypj said:
Maybe a SuzukiGS550 four head or Kawasaki KZ500/550 could be easier to modify?
GS500 is 74 mm bore so would be way too big for a 200 twin (they are below 50mm?)
Just had a thought, what about a VF400/500 head? ;)
sorry just read the bottom sentence we have been looking for a vfr400 head at Teazers suggestion. It takes care of the cam chain issue with a similar gear to the rc166. Found a rear one on ebay a while back... That is on the burner but we need to learn more before we jump in that water. Teazer nailed the pic I posted it was from Giannini's facebook. That string I posted on the cr72 mentioned the mate that built the cb450 head on the cb77 bottom. All I know is all of these "mates" give me hope for humanity.


Sent from my iPad using Tapatalk
 
Need some advice...have the twenty ton press and a metal degree wheel. Throwing away the harbor freight dial indicator. Going to get a good dial indicator. While Zeke is working on his 175 engine build I need to learn how to index the crankshafts. Besides a good dial indicator what do I need?
esyge5y5.jpg



Sent from my iPhone using Tapatalk
 
Lead hammer and V-blocks or centers, (yep, you get to do some 'precision beating' ;D )
You can also use a bronze hammer but they tend to be lighter
I do my XS650 cranks in the lower case running on center bearings only. It works but you have to think about which way DTI is moving compared to if it was on centers
I don't have any problems with the HF DTI, the contact tips need to be tightened up plus they may be 4x48 tpi or 2.5x0.45mm thread,
I had to buy both dies to make extension rods. It kinda sucked the thread varied
 
crazypj said:
Lead hammer and V-blocks or centers, (yep, you get to do some 'precision beating' ;D )
You can also use a bronze hammer but they tend to be lighter
I do my XS650 cranks in the lower case running on center bearings only. It works but you have to think about which way DTI is moving compared to if it was on centers
I don't have any problems with the HF DTI, the contact tips need to be tightened up plus they may be 4x48 tpi or 2.5x0.45mm thread,
I had to buy both dies to make extension rods. It kinda sucked the thread varied
Thank you Crazypj!


Sent from my iPhone using Tapatalk
 
Why do we keep blowing off our megaphones? http://youtu.be/zrPX6xe3Y-k


Sent from my iPhone using Tapatalk
 
Do you have tabs and stays on megga's?
They will never stay in place just clamped to pipe
Pipes look 'wrong'
It looks like you have the right pipe way too long compared to left?
 
crazypj said:
Do you have tabs and stays on megga's?
They will never stay in place just clamped to pipe
Pipes look 'wrong'
It looks like you have the right pipe way too long compared to left?
crazypj first to all to all that have paved our way let me say forgive us...We are to the part of our build where we are learning about exhaust systems. We are also following our credo.."I wonder what what happen if?" Now we know we aren't suppose to run assymetrical exhaust but when we did we broke ninety with our little lucky and that was without megaphones and my big arse on her with a cam that only has .157" lift! Yes carb tuning is a nightmare but really it is two engines sharing a crankshaft? Now if it takes both torque and hp to get to speed at bonneville we will have to make a compromise or will we? What if one helps the other? I learned this from being married for 25 years one is push and one is pull ;) but some how it works. No tabs and stays on the megaphone but we went to the hardware store and picked up some washers and springs...thanks and Lucky's front end has never lifted until now :) can't wait to go to the dyno! My wife has told me if I try to share my crankshaft she will throw a rod. ;)


Sent from my iPad using Tapatalk
 
Texasstar said:
crazypj first to all to all that have paved our way let me say forgive us...We are to the part of our build where we are learning about exhaust systems. We are also following our credo.."I wonder what what happen if?" Now we know we aren't suppose to run assymetrical exhaust but when we did we broke ninety with our little lucky and that was without megaphones and my big arse on her with a cam that only has .157" lift! Yes carb tuning is a nightmare but really it is two engines sharing a crankshaft? Now if it takes both torque and hp to get to speed at bonneville we will have to make a compromise or will we? What if one helps the other? I learned this from being married for 25 years one is push and one is pull ;) but some how it works. No tabs and stays on the megaphone but we went to the hardware store and picked up some washers and springs...thanks and Lucky's front end has never lifted until now :) can't wait to go to the dyno! My wife has told me if I try to share my crankshaft she will throw a rod. ;)


Sent from my iPad using Tapatalk

I'm personally sitting on the edge of my seat. I have changed my thought process. Your greatest power made is with a longer tube on one cyl. Your letting the exhaust length work for you. Sure tuning carbs is differnt. But the wheel leaving the ground. Wth.
The pipes are flying off because they are working. If you can make mid pipes at differnt lengths ( to see what it does when small changes are made)but have them secured via springs or tabs bolting each other. Would that work?
 
Back
Top Bottom