Help — CB500/4 engine. Every screw is frozen.

edelweiss

Coast to Coast
I have a 72 CB500 deemed a parts bike and has and engine that turns (not seized). Only has 37,000 miles on it, but when I bought the bike I did't know that EVERY screw and nut was frozen. They are not rusted on the caps either (oxidation though). I tried heat (small bottles for pipe sweating), but the heat actually makes the caps too soft and they strip. Only got one out.

Any chemical I can use that will penetrate the screws? Mystery oil? Do I do something radical and dip this whole engine in Mystery oil for a week? I don't know. I will try anything. Would like to rescue this engine.

Any help is greatly appreciated!

Thanks,
John
 
an impact screw driver if you dont already have one will save you alot of cussing!
i took a propane torch on an old 350f, let it cool, sit the impact driver on it with as must pressure as you can so it doesn't ride off the screw and hit it with a hammer until its loose. 1 screw alot took me 25 mins of hammering and cussing, and never stripped it.
 
danker16 said:
an impact screw driver if you dont already have one will save you alot of cussing!
i took a propane torch on an old 350f, let it cool, sit the impact driver on it with as must pressure as you can so it doesn't ride off the screw and hit it with a hammer until its loose. 1 screw alot took me 25 mins of hammering and never stripped it.

Thanks... I found this also:

http://www.youtube.com/watch?v=EzoLcXbIur4
 
FreezeandReleasekv_331294_web_606W.png



This stuff has worked wonders for me. It cost around $15 but is well worth it.
 
Honda Phillips head bolts are horrible to be sure. You absolutely must use an impact driver to remove them. Never even try without one and use the right size heads.

Not an electric impact driver - the $5 handheld ones you hit with a mallet. Use a rubber mallet too. Better than a hammer IMHO.
 
you need to use a heavy steel hammer with the impact driver not a rubber mallet
i have tried both, both work, but the steel hammer is far better
 
Hmmm - maybe I'm just not remembering right :) Been a while since I've had to use one.
 
thats ok, i tear down a lotta engines,also gotta be careful how you hold the driver when you smack it some of them have a perfect blood blister pinch point !! :-\ :'(
 
xb33bsa said:
thats ok, i tear down a lotta engines,also gotta be careful how you hold the driver when you smack it some of them have a perfect blood blister pinch point !! :-\ :'(

Not going to hurt if I try the roll pin punch first. If that doesn't work I will try the manual impact driver. Will report my results... Thanks!
 
Don't want to strip your screws? DON'T use a manual impact driver. Just tried it and it f'd up one of my screws. Only tried it because it arrived in the mail before the roll pin punch did. Like the guy in video said... it turns the screw wayyy too fast and turns it with the same 200 lb force it applies in the downward blow. Not good. The downward blow is what shocks the screw loose, not the turning.
 
I've never stripped a screw (that wasn't already stripped) with an impact......hmmm
 
Me neither - make sure you're not tightening it :P I have to manually check the driver every time I use it to make sure it's turning the right counterclockwise direction.
 
Tim said:
Me neither - make sure you're not tightening it :P I have to manually check the driver every time I use it to make sure it's turning the right counterclockwise direction.
This is a very good thought lol
 
edelweiss said:
Don't want to strip your screws? DON'T use a manual impact driver. Just tried it and it f'd up one of my screws. Only tried it because it arrived in the mail before the roll pin punch did. Like the guy in video said... it turns the screw wayyy too fast and turns it with the same 200 lb force it applies in the downward blow. Not good. The downward blow is what shocks the screw loose, not the turning.


they will strip if you dont use the impact driver properly!
 
Tim said:
Me neither - make sure you're not tightening it :P I have to manually check the driver every time I use it to make sure it's turning the right counterclockwise direction.

Double read the directions (see picture below). The friggin thing even turned my bit end to a now pinwheel shape (bent it).
 

Attachments

  • photo.JPG
    photo.JPG
    922 KB · Views: 216
It's gotta be tightening. Put the bit in it and push down on a hard surface and watch which way the tip moves.
 
SONIC. said:
It's gotta be tightening. Put the bit in it and push down on a hard surface and watch which way the tip moves.

Can't tell which way it is turning when smacking it on a cutting board. I can go out and look at the screw, but there is a foot of snow outside. >:(

Please see picture below with the red arrow... does that pin or hole, if pushed in, change the direction of the turn upon impact? Don't know why the directions just say "simply hit". Does not say I can change the direction.
 

Attachments

  • photo-1.JPG
    photo-1.JPG
    941.9 KB · Views: 212
Back
Top Bottom