Hondazuki XLRM250 Trans-America Hell Ride

I snuck away during lunch and got the jug off. It wouldn't be a dirt bike without some dirt and rust, I suppose. The bottom of the cylinder has a bit more rust, but no more than I think a hone won't fix. The piston looks good, while the lower ring explains why this thing was burning oil...

0956b3934128745059c39b23ec29ec08.jpg


332e6be40059c44cf121772350837e68.jpg


a1da3c9bf3be2da6653ffe6996e02955.jpg


e0bb5a3c8cfb91b2c0c9bd091c6ca22c.jpg



Sent from my iPhone using Tapatalk
 
Time to locate the motor. Swinger pivot on these swing arms have an opening, so I machined a sleeve that'll get a zerk. I'm trying to decide if it should be mounted to frame. My inclination is to bracket the top rear motor mount with the frame and the pivot.

83775f9beaf3e230ba35593baa11ab84.jpg


The original 175 rear, bottom motor mount will get recycled. Every other one will need moved..

5fc2540a9a86dd6649db550002c88bcf.jpg


Also worked on sprocket alignment

7cc1f27bd46561b590187303eed4c05e.jpg





Sent from my iPhone using Tapatalk
 
deviant said:
Do you have a pic of the lower rear bolt placement? And where your sprocket is from the side?

I got it down so the chain lays on the swingarm slider with no load, but I cut out the lower frame cradle like the red frame XL185... seems axle, pivot and output shaft all line up

918892fae9a1f89056c71c0cca7a05e0.jpg

1313348313ecff8029116e0325c1e500.jpg
 
Ah. That's an 80s XL motor in a 185 frame. The tranny and crank is smaller on those. The one issue with this 72 motor is it's fat bottom. We're similar but different. 72 XL250 motor in a 73 XL175 frame. I think my solution will still be similar.
 
Tune-A-Fish said:
It's an RM 85 frame


Sent from my iPad using Tapatalk
Ah, gotcha. Still, my main dysfunction with a 1972 XL250 motor is dealing with the pig of a lower end. I have to figure out a way to drop the motor down in the frame to compensate for the extra meat. One question I have is what is required to use a motor as a stressed member? One solution could be to cut out the cradle, convert to stressed member, and run a later model XR or XL (or fab one up) skid plate.
 
I used a sawsall ::) Really tho, you are going to have to cut the frame, the motor will become a stressed member like the new versions or you could calculate the drop build a lowering cradle with tube ends then cut it in with a hole saw: just an idea, the tube ends make the weld strong without a dowel or you could dowel one end or slip notch a second dowel or or or
 

Attachments

  • frame drop.jpg
    frame drop.jpg
    32.8 KB · Views: 1,198
It's not really possible to "convert" a cradle frame to a Stressed member and retain any rigidity.

Leaving aside for a moment the huge amount of work for small gains aspect of the build, the key is to add stiffness without adding much weight. It might be better to remove the bottom rails, drop in the motor and bend up new tubes to replace the lower cradle but leave enough space to get the motor in and out..
 
teazer said:
Leaving aside for a moment the huge amount of work for small gains aspect of the build, the key is to add stiffness without adding much weight. It might be better to remove the bottom rails, drop in the motor and bend up new tubes to replace the lower cradle but leave enough space to get the motor in and out..

Replacing an XL175 motor with an XL250 motor is no small gain. There are many performance upgrades for an XL250, while there are none for the 175. Even in stock trim, the motors are night and day including a 15mph top end speed increase. Which, for a cross country ride will make all the difference. I've also increased ground clearance by 5 inches, modernized the suspension, and added more than 6 inches of shock travel. As far as the stressed member question, that answers it. I'm only about 14mm away on lowering the motor to get it right, so cutting out the bottom of the cradle, bending up some tube and welding back in a modded cradle is really where it was always going to happen.

I'll be less than $1000 all in on this bike when it's complete. Sure, I could'a just gone on Craigslist and bought an XL or XR 200 or similar and done very little, but what's the fun in that? Not to mention, they cost more than $1K.
 
deviant said:
... I could'a just gone on Craigslist and bought an XL or XR 200 or similar and done very little, but what's the fun in that? Not to mention, they cost more than $1K.

That's where I was coming from. What would an XL250 or 350 cost by comparison? I totally get where you are coming from, but had to throw it out there because sometimes we (or I) get carried away with an idea that grows like topsy and a sanity check is useful from time to time. Not that it ever stops me once I get carried away..... :-)
 
teazer said:
It's not really possible to "convert" a cradle frame to a Stressed member and retain any rigidity.

Leaving aside for a moment the huge amount of work for small gains aspect of the build, the key is to add stiffness without adding much weight. It might be better to remove the bottom rails, drop in the motor and bend up new tubes to replace the lower cradle but leave enough space to get the motor in and out..

And yet here: I did it anyway.


RM85 cradle to stressed XL185/200

02972ef28c598adde026a95dfef76dd7.jpg


Donor frame

$T2eC16d,!)8E9s4l8h(qBQE6bKzSUQ~~60_35.JPG


59f905e3b2cb554871fe08a4327d5dda.jpg
 
teazer said:
That's where I was coming from. What would an XL250 or 350 cost by comparison? I totally get where you are coming from, but had to throw it out there because sometimes we (or I) get carried away with an idea that grows like topsy and a sanity check is useful from time to time. Not that it ever stops me once I get carried away..... :-)
Ha! I appreciate that. But the last XL250 I saw come for sale within 400 miles of me sold for over $2k. I haven't seen an XL350 for sale for over a year. I admit, it's just fun to build frankenstein bikes. It's art to me, and I'm in no way trying to be pragmatic about it.
Sonreir said:
Life is an engineering exercise. Why should our projects be anything different? ;D
Exactly how I see it, Matt.
 
It's all good. Looking at that single spine frame I cannot imagine how much it must twist right at the back of the tank where the tubes all meet.

All frames have some twist and some amount of hinge in the middle and maybe small dirt bikes use that extra deflection to soften a rough track and make them more rideable/comfortable.
 
Time for another experiment:

We're going to try a 79-81 XL250s piston with about 2.5mm taller crown to work with. Same bore and stroke between all XLs to 1985...

3b96a9e54ae66bde81638e8c4f837b67.jpg


0dc11ff2e349a7b7f67842bbcb039a58.jpg


4703be3ca7a1129c1b668c9a098f4443.jpg


2d778f3e9c70f1e1cb0ada5ac6b9c852.jpg



Sent from my iPhone using Tapatalk
 
Back
Top Bottom