Hondazuki XLRM250 Trans-America Hell Ride

d917d60c2ee777ba00b7387b24e1f56b.jpg



Sent from my iPhone using Tapatalk
 
to keep it away fro the bottom
when you start getting deep into travel the bottom of the pivot is going to act as a solid unmovable chain tensioner to point of trying to limit suspension travel if it doesn't snap the chain first
 
Much better in the second, you should run a chain slider on top anyway so that will take slap out also, one tooth smaller would get even closer but looks tight already on CS size/count
 
you see the chain is never really in a power loaded situation with suspension fully topped out the bike is pretty much airborn,jumping or thru a whoop sextion at that point so power thru the chain is not at full pull like midway thru
having it on the swinger is not an issue up top because it actually spends little time rubbing and never will rub under power at sag level
but the bottom is a wholle diff can o worms
 
Tune-A-Fish said:
Much better in the second, you should run a chain slider on top anyway so that will take slap out also, one tooth smaller would get even closer but looks tight already on CS size/count
man im not trying to be a argumantive dick but its just way out from where it must be, the forward distance is certainly going to create a lot of variance but the cs is way high. the line would be somewhere close to level so that the chain is laying on top the pivot
you will never see an oem with the line from pivot to cs pointing up like that and thats because bit is an extremely critical design factor , its the number one deal that must be done correctly
a good example is the hallman tt500 the tt500 motor was a design that could not allow a close swinger to cs location. it was impossinle
they delt with it using spring tensioners and the bike worked very nicely although i would bet money more than one time they dnf from chain coming off
us_vehicles.997936.2.jpg
 
Aight mu'fuckers, time to dispense with some drama...

15911f75b26f520fb2a2a09333b3149e.jpg


Sent from my iPhone using Tapatalk
 
Still unable to move on the frame and seat, so I dug up a few small victories on the motor.

I suspect it sat empty for a while and corrosion set in on the magnesium. The clutch was disgusting and the stator side cover had a large patch of corrosion where the cover and rotor are close together. Both the cover and rotor ended up with heavy pitting...

Nothing that can't be resolved.

39fa8a368228dda8b10be5d5b07b7a38.jpg


I machined down the rotor surface to clean it up and true it.

93aee6857b3a23446fd42a11f36f29c0.jpg

7b0d175653cf71839b657cf97d46a93c.jpg


As indicated, the clutch is fucked. I ordered a set of friction discs and resurfaced the metal discs. I also honed and resurfaced the jug and cleaned, polished and re-ringed the piston...

c05fcf27bd50d623ac3d2dfb510169b8.jpg


5b977059ee1e2ca5f771485e6872781f.jpg




Sent from my iPhone using DO THE TON
 
Nice! cant wait to see the frame get 100% and this lump start coming together. That'll keep you in a solid 2nd place haha. I'll probably finish mine around Aug 14. a day before drop dead timing :/
 
i got some good steel plates and lots of those bottem end parts yours for the shipping+ a pittance if you need em
 
xb33bsa said:
i got some good steel plates and lots of those bottem end parts yours for the shipping+ a pittance if you need em
Yessir. Give me a price and I'll Paypal away.
 
deviant said:
Yessir. Give me a price and I'll Paypal away.
just steel plates,how many
ill gather them up this evening and we can do details latr, gotta run ,out to go hobo camp boneyard sickle pikin for a few hrs now tho
 
Back
Top Bottom