Hondazuki XLRM250 Trans-America Hell Ride

they look like the ones i got but i coont use the ones i got as a headlight :-[ it would sue-ee-side
the bike looks and sounds great! and you have pulled some uphills wot in upper gears?
 
xb33bsa said:
they look like the ones i got but i coont use the ones i got as a headlight :-[ it would sue-ee-side
the bike looks and sounds great! and you have pulled some uphills wot in upper gears?
Used em as headlights on the 175. They worked on that bike. They're plasma LED rock lights with projector lenses. I haven't tested it above 40mph or off of my street since I have no front brake. Still waiting on the m/c rebuild kit.
 
ced9f17392a6941483b387662664a856.jpg


First attempt at a seat cover is okay . This shape is hard as hell. I'll wear it out a bit, then redo it.


Sent from my iPhone using DO THE TON
 
The other muffler basically blew off from back pressure and melted my new seat cover (time to make another), so I made another with this Vance & Hines I've reconfigured on two other bikes. I also wrapped the pipe around the head and through the frame to get the heat away from my legs...

95c17b6300d33f953d0a96f501a1f266.jpg


I'll machine another end cap, because this one is too open and loud af.


Sent from my iPhone using DO THE TON
 
Pipe looks good. If i get that far, I think I'll do a high exhaust and possibly through frame. Hows it running with that length/muffler? I'm looking to source a relatively cheap can not too loud and looks like it belongs on an offroad bike.

Oh - also - whatd you do for the exhaust collar? Is it from an OEM header or did you turn one up from scratch?
 
adventurco said:
Pipe looks good. If i get that far, I think I'll do a high exhaust and possibly through frame. Hows it running with that length/muffler? I'm looking to source a relatively cheap can not too loud and looks like it belongs on an offroad bike.

Oh - also - whatd you do for the exhaust collar? Is it from an OEM header or did you turn one up from scratch?
Header is stock XL. It's a "J" pipe that runs just past the top end. I cut it back a couple of inches to accommodate the bend through the frame. It's CB 750 pipe from there to the muffler. The way the stock 750s run a separate flange that the headers slide onto made it nice for a coupling like fitting at the end of the XL header. I haven't run it with this pipe yet. I ran it with the KX muffler before, which was way too restrictive. It had great torque through the gears though. I need to machine a new end cap with a smaller hole on this one. Right now it's about 3/4" wider at the end than the rest of the exhaust, which makes for a really loud pipe.
 
deviant said:
ced9f17392a6941483b387662664a856.jpg


First attempt at a seat cover is okay . This shape is hard as hell. I'll wear it out a bit, then redo it.


Sent from my iPhone using DO THE TON
the way the seat is shaped ??? :o you wont be innit much anyway
what was reasoning in the thing being shaped so almost perfectly wrong ?
 
xb33bsa said:
the way the seat is shaped ??? :o you wont be innit much anyway
what was reasoning in the thing being shaped so almost perfectly wrong ?
Please explain how the seat is shaped so almost perfectly wrong. If you mean extremely comfortable, than yeah, it's extremely perfectly wrong. No almost about it.
 
Just for reference, since it's so confusing, I'm trying to make a seat that is a cross between this:

honda%20XR200R%2084.jpg


and this...

honda-xl-600-r-02.jpg
 
when trail riding you need to remember the secret formula

beer x speed divided by drop off height over the factor of tree density = required thickness of the nutsack pad
 
Haha!

So in their infinite wisdom, Honda designed the head with a hole in it so you can get to a nut on the cylinder head. That hole has a plug which decided to leak. A drain stop in the head. Genius. Got another one machined up.

53b226313b8d19b86e4e8b7861e4767e.jpg


b275d9121a52b54969436a41a1a21fec.jpg


Shazam!

489ea800b4cbadfde547fd156c8cf48c.jpg




Sent from my iPhone using DO THE TON
 
deviant said:
Please explain how the seat is shaped so almost perfectly wrong. If you mean extremely comfortable, than yeah, it's extremely perfectly wrong. No almost about it.

it has a big v in the middle where you are stuck, it will make it a chore to slide forwards or back which is what you naturally want to do to get weight on the front tar and if you dont you either are going way to slow or you warshout the front and layerdown
the shape you made,ts just never done cause it sucks
 
deviant said:
Haha!

So in their infinite wisdom, Honda designed the head with a hole in it so you can get to a nut on the cylinder head. That hole has a plug which decided to leak. A drain stop in the head. Genius. Got another one machined up.

53b226313b8d19b86e4e8b7861e4767e.jpg


b275d9121a52b54969436a41a1a21fec.jpg


Shazam!

489ea800b4cbadfde547fd156c8cf48c.jpg




Sent from my iPhone using DO THE TON

thats nice work ;) you need the peg it contacts the rocker cover and pins down that plug. it could just be threaded m6 and a short stud screwed in to correct length ....but you gotta have it ...when i was 15 and got my xl250 in 1973 i decided it coont be that hard to put a big top piston in there
took me fucking forever to find that 4th nut :o :D
i didnt have any mechanical experience re engine teardowns,and no shop manual

sorry about dogging the seat but i assumed it was a late april fool and you would unviel the real seat later :-[ :-\ i assumed you had offroad riding experience enough to know
 
xb33bsa said:
thats nice work ;) you need the peg it contacts the rocker cover and pins down that plug. it could just be threaded m6 and a short stud screwed in to correct length ....but you gotta have it ...when i was 15 and got my xl250 in 1973 i decided it coont be that hard to put a big top piston in there
took me fucking forever to find that 4th nut :o :D
i didnt have any mechanical experience re engine teardowns,and no shop manual

sorry about dogging the seat but i assumed it was a late april fool and you would unviel the real seat later :-[ :-\ i assumed you had offroad riding experience enough to know
Haha. Thanks for saying. I'm pretty confident I've got my balls covered. My ass is in the low part of the saddle. Maybe it needs to go up hight, but we'll see I supposed. Sure will feel it if it's not right. LOL

I didn't know about the pin dealio. Thanks a bunch there. I wondered why is was so damn tall stock. Once I pulled it, it wouldn't go back tight. The O ring was flat and every O'ring kit I've found doesn't have that ring nor are they as big of a ring to fill the stock plug. It's a thick fucker. Looks like a drill and tap is in order.
 
Ha. Nice work Eric. Just ride the piss out if it. Oh and I am officially whisky drunk and full of IV antibiotics so my opinion is useless.
 
Maritime said:
Ha. Nice work Eric. Just ride the piss out if it. Oh and I am officially whisky drunk and full of IV antibiotics so my opinion is brilliant and I'm automatically smarter than I was a day ago.
 
Back
Top Bottom