Oh Lord (CB500) - The Leaky Bitch (p. 31)

Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

sounds good. i have a bunch of fresh crush washers ready to go.

in other problems; i was tightening down the bolt thats the drain plug for one of the forks, and it kept spinning with very little force. it spun the head all the way off, with the rest of the bolt stuck in the fork but about 1/32 of an inch. I ordered a really small tool for backing out bolts/screws that are stripped/broken. i'm crossing my fingers that this thing will work to get the bolt out or i am SCREWED. (really, no pun intended.)
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

Ranger, maybe I'm missing the obvious, but is the bolt broken off below the level of the plug, or above it? Could you carefully weld a nut onto the snapped bolt and use that to pull it out? Or even weld another bolt onto the exposed nub of the broken bolt? I've had really really horrid luck with those "ez-out" tools... they always break off at just the wrong time and happen to be made of hardened steel, so they are next to impossible to drill out. My only other thought would be to try to take the actual level of the material surrounding the bolt down just far enough that you could grab the nub with a pair of vise grips... Kinda a destructive way of doing it, but... anyway, stuck bolts suck -- sorry to hear that this happened to you! :(
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

Usually, as a rough guide, you want at least same amount of thread in hole as diameter of bolt
Banjo bolt is 10mm dia, you should have around 10mm thread below banjo union (plus crush washers)
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

here is the broken bolt:
IMAG0198.jpg
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

spark6 said:
Ranger, maybe I'm missing the obvious, but is the bolt broken off below the level of the plug, or above it? Could you carefully weld a nut onto the snapped bolt and use that to pull it out? Or even weld another bolt onto the exposed nub of the broken bolt? I've had really really horrid luck with those "ez-out" tools... they always break off at just the wrong time and happen to be made of hardened steel, so they are next to impossible to drill out. My only other thought would be to try to take the actual level of the material surrounding the bolt down just far enough that you could grab the nub with a pair of vise grips... Kinda a destructive way of doing it, but... anyway, stuck bolts suck -- sorry to hear that this happened to you! :(

I forgot to mention on facebook that welding something on it and backing it out is also an option. If you have a welder. If you know how to weld.
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

It kinda sucks that forks are built, the easy way to do it would be drill through.
Drill bit will probably 'catch' and screw it inside fork
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

Good news at the cost of money that was not in the budget for my little project!

I found my lost banjo bolt; it was stuck to the bottom of one of my magnetic bolt dishes. I had already paid $13 to have a replacement shipped out, and I think I would rather use the original one because its longer.

And then there is the broken fork drain...

IMAG0200.jpg


I purchased a set of drill bits for metal for $25, a set of broken bolt extractors for about $20, a mini-bolt extractor for $10, and a T-handle for $8. The bolt came out pretty easy! I hit it with one of the drill bits and it spun right out.

So I spent $43 on tools that were not in the budget at all, and only used the $25 drill set to get it out. Arghhhhh! At least it is out and I have the tools for other things in the future.

So I only need to purchase a couple of more things: oil, fork fluid, jets, and a battery. This little detour kinda delayed that, but oh well.
 
Re: Oh Lord (CB500) - 05/22/2012 Banjo bolt question (pg. 22)

it did feel good to get it out without running somewhere for help. i was disappionted I had to have teh swingarm pressed apart by a shop. this felt like a victory.
 
Re: Oh Lord (CB500) - 05/27/2012 Help! Brakes are hard!!! (pg23)

Yesterday, I carefully masked my master cylinder and painted it. Then once it was dry, I rebuilt it with a fresh rebuild kit and my trusty Honda service manual.

Once I went to install and bleed it, it began puking brake fluid all over the nice paint and totally ruined that. I did some looking, and found out the service manual is pretty much crap as far as twlling you how to put the parts in the mster cylinder. Once I put one of the rubber thingies on the piston where it was supposed to go, I reassembled the master cylinder and retried bleeding the brake.

Success! Well maybe. I pumped all of the air out, closed the bleeder, and the brake is HARD without much travel at all in the lever. Whats going on?

I am going to double post this in the Wheel/Tire/Brakes section...
 
Re: Oh Lord (CB500) - 05/27/2012 Help! Brakes are hard!!! (pg23)

If not much travel and the brake does not drag then you got it right . If drag and possible increasing drag then the pressure relief hole is plugged by improper assembly , dirt , grit , smeg , boogers , bugs , politicians , lawyers or worse .

~kop
 
Re: Oh Lord (CB500) - 05/27/2012 Help! Brakes are hard!!! (pg23)

Swivel said:
That bike is a junker for too much cash...Avoid it...The later CB550 has a lot of the early problems solved...Far better to be patient and wait for the DEAL,than be sucking lemons for three years with a money pit and tears before bedtime....

Ouch! Thats kinda critical. Yeah, I paid too much for it. Chalk that up to inexperience. But until these past couple of weeks, its been easy sailing working on this thing. Its almost done and its looking great.

Left on the list to do:
-finish draining both forks and refill with fresh fork oil
-finish up wiring
-fix front brakes
-adjust geometry of rear brakes
-properly jet carbs and try to get started
 
Re: Oh Lord (CB500) - 05/27/2012 Help! Brakes are hard!!! (pg23)

I'm glad to see you making some good progress. Since I live near the ATL I'd really like to see the finished product in person some day. Any ideas what kind of paint you're going to go with?
 
Re: Oh Lord (CB500) - 05/27/2012 Help! Brakes are hard!!! (pg23)

I'm thinking metal flake royal blue with orange and white pinstriping, and a 60's style racing number on the bum stop. Hot Rod Walt (Richards) of the Psycho Devilles will be laying the stripes once its ready!
 
Re: Oh Lord (CB500) - 06/06/2012 minor update, handle bars done (pg24)

a little progress last night...
I managed to get the handlebars all set up.

IMAG0216.jpg


IMAG0215.jpg


Next to tackle is the wiring.
 
Re: Oh Lord (CB500) - 06/06/2012 minor update, handle bars done (pg24)

looking good John. sorry I haven't been in touch. My A/C died at the house and the roommate hasn't gotten it fixed yet so I have been at the new house.
 
Re: Oh Lord (CB500) - 06/06/2012 minor update, handle bars done (pg24)

03rangerxlt said:
a little progress last night...
I managed to get the handlebars all set up.

IMAG0216.jpg


IMAG0215.jpg


Next to tackle is the wiring.

love the handlebars mate, looking awesome
 
Re: Oh Lord (CB500) - 06/13/2012 minor update, no pics (pg24)

I drained and then pumped the foul smelling (but clean looking) oil out of my forks, flushed them with solvent, blew then out with compressed air, and then refilled them with 10w fork oil. Man, 5.4oz is not that much at all.

I also made a big mess on my garage floor with foul smelling fork oil and solvent. Luckily, I had it cleaned up before the wife got home, and the solvent smell is mostly masking the foul fork oil smell.

I also learned what the wiring harness on one of these is supposed to look like. It turns out that the previous owner cut apart the wiring loom and started subtracting stuff from the wiring harness. Stuff that I'm not prepared to do without as a novice rider. Stuff like the oil preasure light, and the neutral light!!! I found a complete second hand harness for $30, and it should be here tomorrow.

Another issue I'm having is with the iginition system on this thing. Someone really cranked down hard on the screws holding in the old breaker bits in, and the heads are starting to strip. So for now, I am leaving them alone until I can borrow a friend's impact driver.

Damn, I am getting so close!!!!
 
Re: Oh Lord (CB500) - 06/13/2012 minor update, no pics (pg24)

Keep plugging away man, you can do it.
 
Back
Top Bottom