"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
on the stator well it will hacve deposits be careful trying to clean that if it is stuck just leave it alone
clean gasket surfaces to bare metal 100%
what i was talking about is the sprocket and related bits bolted to the stator rotor

Ok will do. Did you notice anything that looked suspicious like a crack? I don't see a dang thing. Is there any way to check for it? You mentioned talc. I'll try that and see if it reveals something.




Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Took this beast for a spin. Not really used to counter steer like that. Took me a mile to realize I didn't need to use the handlebars. You lean, it goes.

7e4u8anu.jpg



Sent from my iPhone using Tapatalk
 
My next purchase:

http://www.liquidchopperstore.com/kms-1.html

My shocks now are way too long and I'm tired of my chain rubbing. I have a chain slider glued to my swinger but it keeps throwing rubber pieces at my sprocket so I'm tired of that.

It says it has an adapter for smaller and larger bolts....I'm assuming this is referring to the ability to use a 10mm bolt or an 8mm bolt, a common conundrum for these swingarm bushings...?
 

Attachments

  • yhst-14106668183646_2258_837174865.jpg
    yhst-14106668183646_2258_837174865.jpg
    94.9 KB · Views: 529
When my friend had owned my 175 put something that looked like that on the bike. They were a rather soft springrate. Softer than the original rusty ones that were on the bike when he bought it.

As seen on page 8 of:
http://www.dotheton.com/forum/index.php?topic=11996.105
 
Re: "Patina" The 1973 CB175 Cafe Racer


acm177 said:
When my friend had owned my 175 put something that looked like that on the bike. They were a rather soft springrate. Softer than the original rusty ones that were on the bike when he bought it.

As seen on page 8 of:
http://www.dotheton.com/forum/index.php?topic=11996.105

Hey man, thanks for the info. Right now I have DCC shocks on there and I can't even get them to compress when I'm sitting on them. I've adjusted them to their "springiest" setting and can't get them to budge unless I'm really hopping on it.

I don't weigh very much. If actually like a little more soft I think. I'm actually thinking of contacting hagon too...
 
From what I have observed Hagon is the way to go.

Additionally-- have you thought of taking out that bottom short spring? But the upper might be too short, or not fit on the bottom perch.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Hey man, thanks for the info. Right now I have DCC shocks on there and I can't even get them to compress when I'm sitting on them. I've adjusted them to their "springiest" setting and can't get them to budge unless I'm really hopping on it.

I don't weigh very much. If actually like a little more soft I think. I'm actually thinking of contacting hagon too...
Hagon is the best. But do you need the best. I wound up getting mine off flea bay for $50. Actually it's not a bad shock. Once you take them apart and fill it with the added fluid it needs. The Chinese skimp on the oil weight -due to shipping costs. And you take them apart to make sure the shock was not built on the sixth and last day of the work week. I set the bump stops all the way up in order to use them as a gauge, and had my foxy lady sit and bounce- that part was not a part of the test- . They moved 1.75".... So know they are soft. I run them with more tension on spring. Granted I had to modify the bottom shock rubber and spaced out the top mount with ss 1/2" washers.
 

Attachments

  • image.jpg
    image.jpg
    270 KB · Views: 281
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Hagon is the best. But do you need the best. I wound up getting mine off flea bay for $50. Actually it's not a bad shock. Once you take them apart and fill it with the added fluid it needs. The Chinese skimp on the oil weight -due to shipping costs. And you take them apart to make sure the shock was not built on the sixth and last day of the work week. I set the bump stops all the way up in order to use them as a gauge, and had my foxy lady sit and bounce- that part was not a part of the test- . They moved 1.75".... So know they are soft. I run them with more tension on spring. Granted I had to modify the bottom shock rubber and spaced out the top mount with ss 1/2" washers.

Haha glad your lady was there to help...

Two things, I was going to get some of those shocks but the reservoir interferes with my muffler. Also I certainly don't need top of the line. Those red wings were $130 and I think I can swing that. If Texas star ran them, they have to be good ;)
 
the redwings are a good choice although the springs they have on them are likely too stiff,after all they are listed as being suited for a 450 which weighs an easy 130lbs more than your 175
but springs they are easy to change and not all that expensive
 
Re: "Patina" The 1973 CB175 Cafe Racer

Gasket surfaces all clean and ready to go. Haven't decided on gasket sealer or going without or only going with it on one side..

dy4equ5u.jpg


sabezy2a.jpg
 
loctite 518 if you are using sealer i already tole you it is far better than anything else
you could use some all around that wiring rubber case plugging as well
'specially if the rubber is hard
if i am using it to bond a gasket i spread a very thin layer with a popsikle stick
i usually like to stick the gasket to the outer part
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
loctite 518 if you are using sealer i already tole you it is far better than anything else
you could use some all around that wiring rubber case plugging as well
'specially if the rubber is hard
if i am using it to bond a gasket i spread a very thin layer with a popsikle stick
i usually like to stick the gasket to the outer part

Yup I was planning on using nothing less than the loctite stuff you told me about.

You answered my last question about which part to seal. Thanks!
 
xb33bsa said:
loctite 518 if you are using sealer i already tole you it is far better than anything else
you could use some all around that wiring rubber case plugging as well
'specially if the rubber is hard
if i am using it to bond a gasket i spread a very thin layer with a popsikle stick
i usually like to stick the gasket to the outer part

Hey XB, could I also use that Loctite 518 as a threadlocker on the bolts below nominal oil level? I noticed on the description it filled gaps of .25mm and figured it may help. Would that screw up my threads when I have to remove the bolts in the future?
 
it works very well as a thread sealant just make sure clean with something like brake clean and let it cure for 24hrs
oh and it is removable not preiminent
 
Re: "Patina" The 1973 CB175 Cafe Racer

Bought some Gunk from the store to clean up this CL200 engine. I've decided I'm going to try to rebuild this one myself and see if I can fit it and the 200 carbs in the 175. Should just bolt right up with a different clutch routing path.

Before:

re5yhaga.jpg


7abu8ady.jpg


anegamug.jpg


upy6apu8.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

Looks like I'm going to have to use the gel cleaner multiple times....

After gunk and pressure wash.

e9u7erer.jpg


namusyvy.jpg


amu6aget.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

And on the way back from the DIY car wash thing the motor took a tumble and somersaulted around the back of the jeep. Made me think I should drain the oil before I haul it around everywhere. This is going to be a problem . I guess the only thing to do is take it to someone with an impact wrench and see what they can do. It's stripped so bad an 18 mm almost fits.

ahunudu6.jpg
 
1sttimer said:
I've decided I'm going to try to rebuild this one myself and see if I can fit it and the 200 carbs in the 175.

The 175 carbs are the more desirable carburettors if I remember correctly. I gave them up for some newer Keihin PE units, so I might be off.
The 200 has the larger oil pump which is a bolt on...

Is the sprocket the same tooth size as the one on your 175? I recall that your 175 has some 200 parts allready.
 
Re: "Patina" The 1973 CB175 Cafe Racer


acm177 said:
Additionally the 200's stator puts out more watts than the 175's...

Good info. I actually thought it was backwards from some post I read a while back...may have been yours? Or in hondatwins Idk.

I'm just doing the engine because I need another decent project and don't have the funds for a whole new bike till after the wedding.

The carb conversation is one I need to have. I was getting ready to drop some cash (albeit not much cash) on a set of 200 carbs as one was missing on this one when I got it
 
Back
Top Bottom