"Patina" The 1973 CB175 Cafe Racer

Texasstar said:
Initially when we rebuilt ours it turned over easy. But when we changed to single valve springs we put it in coil bind. It started and loped like a Harley and also spewed oil like one for a few seconds and then we disassembled and found the problem and switched to our other valve springs.

Anything shiny in the oil?


Sent from my iPhone using Tapatalk

I suppose I misspoke when I said "everything was disassembled." The head, valves and springs were left alone. I had them lapped before the entire disassembly but other than that it's stock up there.

There's nothing in the oil but fresh oil because I haven't gotten it to fire yet. Going to roll it off and see what happens.

Unless you have a cb200 engine laying around ;)


Sent from my iPhone using Tapatalk
 
Texasstar said:
Also the first time you fire up make sure you are getting oil to the top the engine


Sent from my iPhone using Tapatalk

Just take the cylinder head cover off and take a peek?


Sent from my iPhone using Tapatalk
 
We remove the tappet covers now each time we fire up after we remove the head. I also blow smoke through the cam to make sure it is clear. Better to blow smoke than to have it smoked. Are you sure your cam timing is correct?


Sent from my iPhone using Tapatalk
 
Texasstar said:
We remove the tappet covers now each time we fire up after we remove the head. I also blow smoke through the cam to make sure it is clear. Better to blow smoke than to have it smoked. Are you sure your cam timing is correct?


Sent from my iPhone using Tapatalk

What happened in these similar stories? Things too tight? The electronic ignition installed correctly and as instructions said, so I would imagine that would be a fail proof way to make sure timing was right....?? Would 180 degrees off cause this? I was getting a spark while holding the plug against a acorn nut right where I should have spark.


Sent from my iPhone using Tapatalk
 
That I don't know. Maybe Matt would know. I just like at the 175 shop manual and I can't find the installation procedure that is in the 200 manual


Sent from my iPhone using Tapatalk
 
2u7u8e6e.jpg
here is the 200 procedure


Sent from my iPad using Tapatalk
 
1sttimer said:
What happened in these similar stories? Things too tight? The electronic ignition installed correctly and as instructions said, so I would imagine that would be a fail proof way to make sure timing was right....?? Would 180 degrees off cause this? I was getting a spark while holding the plug against a acorn nut right where I should have spark.


Sent from my iPhone using Tapatalk

Just to clarify, valve timing and ignition timing (though related) are different things.

Having your valve timing off may damage your engine by trying to open your valve at the incorrect time. That's worst case scenario. Often it can just lead to poor running or failure to run depending on how far out it is. Having your valve lash set incorrectly will also change the valve timing.

Having ignition timing incorrect will usually manifest as a loss in power, overheating, or just plain failure to run.

Finally, having valve timing off (specifically by skipping one or more teeth on the cam chain) will affect ignition timing as well.

If the top end of the engine has been apart, then there would have been the potential to mess up the valve timing. There's also the possibility that it was never correct to begin with.
 
We have installed the cam chain tensioner backwards that will also put things in a bind.


Sent from my iPhone using Tapatalk
 
Texasstar said:
Matt we need a DTT start up procedure


Sent from my iPhone using Tapatalk

That's a good idea. I found a page on Dans Motorcycle Webpage here that may be of some use:

http://www.dansmc.com/starter.htm



Sent from my iPhone using Tapatalk
 
It sounds to me like there is still something amiss with the clutch engagement if its tight.

If you take the clutch plates out of the clutch assembly and turn the crank with a wrench will it rotate 360 degrees?

Additionally if you back out the tappet adjusters all the way does that change the 'tight' feeling?
 
it can't be anything to do with the clutch
do you have the starter hooked up ?
when in neutral can you freely turn the output shaft ?
in other words your trans is shifting and not binding ?
 
No starter. Intentionally had the harness built without it and intended to run kick only.

I can turn the engine over 360 degrees with any clutch scenario at the alternator.

You can bash me for asking this one more time, but tight crank seals and such wouldn't cause this?

I'll have to try the tappet relief trick next.




Sent from my iPhone using Tapatalk
 
1sttimer said:
You can bash me for asking this one more time, but tight crank seals and such wouldn't cause this?

Nope. If the seals are too tight (e.g. used the wrong ones during the rebuild), then they won't last very long anyway. I think you're in a situation where the engine has to come apart in order to find the issue. If it were me, I'd start with the head. Get the rocker box off to the top of the engine and see if it turns over any easier. If not, then the cam comes out and try again. Still no joy then the cylinder jugs come off. Finally, you're down to either the crankshaft or the transmission.
 
it could be the cam endplay is less than zero(too thin or no gaskets COULD do this) unloosen one side see what happes the 4 screws in the end housing tach drive side would be easiest
 
the other check is to unloosen cam chain tension and if you can easily rock the crank back and forth(to the limits of cam chain slack) then it is up top(the binding)
this is all a process of elimination it has to be something simple
 
Back
Top Bottom